Return to search

Investigation of Tensile Strength of Carbon Fabric-Reinforced Cementitious Matrix (FRCM) at High Temperatures

Maintenance and rehabilitation of existing masonry and reinforced concrete structures are of great importance in the field of civil engineering. Due to deterioration and severe environment, numerous structures fail to meet functional or safety requirements, and as a result, they should be strengthened. Several methods have been utilized to repair the structures, including steel plate bonding, cable post-tensioning, and section enlargement. However, these methods bring disadvantages, such as significant added dead load and high labour cost. Therefore, externally bonding with composite materials has attracted considerable attention recently.
Externally bonded fibre-reinforced polymer (FRP) sheets have been widely used to strengthen reinforced concrete and masonry structures. FRP has been a common method to provide a higher service life for structures for several decades. However, strengthening structural members with FRP introduces certain drawbacks, such as their poor performance in fire scenarios caused by the rapid softening of the polymer-based resin. An alternative strengthening system known as a fabric-reinforced cementitious matrix (FRCM) has been developed to address this issue by replacing resin-based material with an inorganic cementitious-based matrix. Nonetheless, the performance of FRCM at high temperatures has not been investigated sufficiently so far. Hence, this research focused on the mechanical behaviour of FRCM at high temperatures.
This experimental research investigates the tensile performance of carbon FRCM at high temperatures. First, the temperature distribution within the specimens during heating was studied using nine specimens with one, two, or three layers to reveal the required time for the inner fabric to reach a steady temperature. Then, the tension and stiffness degradation of FRCM coupons were studied at different temperatures. A total of 84 FRCM coupons were fabricated and tested in tension; 60 of the tests were conducted at steady-state conditions in which temperature was held constant and load increased, and 24 specimens were carried out in transient-state tests, in which load was constant, and temperature grew. In order to provide a more comprehensive knowledge concerning the FRCM composite, some key variables were included in this research. These parameters are the number of layers (1, 2, 3) leading to different thicknesses (20, 30, 40 mm), the orientation of the fabric layer (unidirectional and bidirectional), target temperature (ambient, 100, 200, 300, 400°C), and heating condition (steady-state, transient state). These tests aimed to reveal the primary mechanical characteristics such as ultimate strength and cracked elastic modulus at different temperatures and compare them with control specimens tested at room temperature.
With the increase in the number of fabric grids from one to two and three, the stress at failure decreased by about 11 and 18%, respectively. With regards to cracked elastic modulus two and three-layered specimens showed 18 and 20% reduction in value. It is also noteworthy to mention that overall load capacity of specimens rose with the increase in number of layers; however, due to the more significant increase in area, the stress was reduced. The same decreases in the cracked elastic modulus and ultimate strength were observed as the target temperature increased. Increasing the temperature to 400°C led to a decrease in ultimate strength and cracked elastic modulus of approximately 60 to 70%. Furthermore, the bidirectional specimens showed a better behaviour than unidirectional specimens in terms of ultimate strength; however, their cracked elastic moduli were almost the same. With regards to the transient-state tests, as the material became thicker, the failure temperature increased considerably. For instance, a 20-mm specimen failed at 467°C with a 20% sustained load, while a 30-mm specimen failed at 558°C. Another vital parameter studied in transient-state tests was the decrease in temperature with the increase in sustained load. An example of this is the 20-mm specimens which failed at 352 and 258°C, while they were preloaded to 40 and 60% of their capacities. The conclusions of this study suggest that FRCM materials do retain a non-negligible strength capacity at high temperatures. However, further investigations to reveal FRCM bond behaviour and retrofitted structural members at high temperatures are still required to provide comprehensive knowledge.

Identiferoai:union.ndltd.org:uottawa.ca/oai:ruor.uottawa.ca:10393/43533
Date29 April 2022
CreatorsAsgharigharakheili, Hamidreza
ContributorsNoël, Martin, Hajiloo, Hamzeh
PublisherUniversité d'Ottawa / University of Ottawa
Source SetsUniversité d’Ottawa
LanguageEnglish
Detected LanguageEnglish
TypeThesis
Formatapplication/pdf
RightsCC0 1.0 Universal, http://creativecommons.org/publicdomain/zero/1.0/

Page generated in 0.0023 seconds