The scope of this licentiate thesis is the investigation of carbon based thin films suitable for rolling components, especially roller bearings. Carbon and carbon nitride are materials with advantageous tribological properties and high resiliency. Such materials are required in order to withstand the demanding conditions of bearing operation, such as high loads and corrosive environments. A fundamental condition for coated bearings is that the deposition temperature must be striktly limited. Thus, carbon nitride (CNx) thin films were synthesized here at low temperature of 150 oC by different reactive magnetron sputtering techniques, which are mid-frequency magnetron sputtering (MFMS), direct current magnetron sputtering (DCMS), and high power impulse magnetron sputtering (HiPIMS). While DCMS is a very well studied technique for carbon based films, MFMS and HiPIMS are relatively new sputtering techniques for carbon, and especially CNx depositions. Using different magnetron sputtering techniques, different ionization conditions prevail in the chamber during each process and influence the obtained film properties at a great extent. It was found that bias duty cycles and the amount of working gas ions are key parameters and affect the morphology and microstructure as well as the mechanical response of the films. Moreover, different bias voltages, from 20 V up to 120 V were applied during the processes in order to investigate the changes that the different ion energies induce in the film structure. The structural, mechanical and tribological properties of CNx films are also presented in this licentiate thesis. The morphology of CNx films strongly depends on both the deposition technique and ion energy. The special configuration of MFMS mode produces highly homogeneous and dense films even from low applied bias voltages, while in HiPIMS mode high bias voltages above 100 V must be applied in order to produce films with similar structural characteristics. DCMS is also proven as a good technique for homogeneous and dense films. Low bias voltages do not favor homogeneous structures, thus at 20 V all techniques produced films with columnar structures with intercolumnar voids. High bias voltages influence the N incorporation in the films, with the appearance of re-sputtering of N-containing species and a promotion of sp2 bonding configurations with increasing ion energy. Nevertheless, the different deposition mode influences the sp2 content in different ways, with only MFMS showing a clear increase of sp2 content with increasing bias voltage and HiPIMS showing relatively constant sp2 content. The morphology and microstructure of the CNx films affects their mechanical response, with higher ion energies producing harder films. A dependency of hardness and elastic modulus with increasing ion energy was obtained, where for all deposition modes, hardness and elastic modulus increase linearly with increasing bias voltage. Films with hardness as high as 25 GPa were synthesized by MFMS at 120 V , while the softer film yielded a hardness of 7 GPa and was deposited by HiPIMS at 20 V . The elastic recovery of the films differs with increasing ion energies, presenting a correlation with the C sp2 bond content. The highest elastic recovery of 90% was extracted for the film deposited by MFMS at 120 V and is a value similar to the elastic recovery obtained for FL-CNx films. All films developed compressive residual stresses, depending also on the ion energies and the deposition mode used. It is demonstrated that the induced stresses in the films increase when denser and more homogeneous film morphologies are obtained and with higher Ar intercalcation. Low friction coefficients were obtained for all films between 0.05 and 0.07, although the deposition conditions are not detrimental for the development of friction coefficient. The wear resistance of the films was found to be dependent on the morphology and to some extent on the microstructure of the films. Harder, denser, and more homogeneous films have higher wear resistance. Especially, CNx films deposited by MFMS at 120 V present no wear. The tribological characteristics of the surface of the films were also investigated at nanoscale by a new reciprocal wear test. In this wear test, the recording of the track profile is performed in between consecutive test cycles, eliminating also thermal drift. The very low wear of the films deposited by MFMS at 100 V and 120 V revealed that during the wear test a phase transformation on the surface may take place, possibly graphitization. It is also demonstrated the way that the surface characteristics, such as asperities and roughness affects the tribological measurements. Attention is also turned to the presence of large asperities on the film surface and the way they affect the obtained average friction coefficient and tribological measured data. / <p>The series name <em>Linköping Studies in Science and Technology Licentiate Thesis</em> is incorrect. Correct series name is <em>Linköping Studies in Science and Technology. Thesis</em>.</p>
| Identifer | oai:union.ndltd.org:UPSALLA1/oai:DiVA.org:liu-118349 |
| Date | January 2015 |
| Creators | Bakoglidis, Konstantinos D. |
| Publisher | Linköpings universitet, Tunnfilmsfysik, Linköpings universitet, Tekniska fakulteten, Linköping |
| Source Sets | DiVA Archive at Upsalla University |
| Language | English |
| Detected Language | English |
| Type | Licentiate thesis, comprehensive summary, info:eu-repo/semantics/masterThesis, text |
| Format | application/pdf |
| Rights | info:eu-repo/semantics/openAccess |
| Relation | Linköping Studies in Science and Technology. Thesis, 0280-7971 ; 1714 |
Page generated in 0.0019 seconds