The objective of a coating operation is to transfer a defect free liquid film
onto a continuous substrate in order to meet the requirements of the final products.
Mainly two concerns govern the process. The first concern is the economics of the
process and the second concern is the quality of the coated film. The economics of
the process are dictated by the speed of coating and the film thickness. Clearly,
higher speeds mean better productivity hence less cost of operation and thinner
films are desirable because less material is being used. Quality is governed by film
uniformity and integrity, indicating that the film will perform as designed. Film
defects such as streaks or tiny air bubbles are indication that the film properties are
not uniform rendering it unacceptable to customers. One of the most versatile
coating systems to achieve thin films at high speeds is reverse roll coating which has
been used for a long time all over the world. At low speed, typically 1m/s, this
coating operation is inherently stable and with small gaps of order 100 microns can
ii
lead to film thickness of order 30-50 microns. Much research, theoretical and
experimental, has been devoted to this coating flow but only at low speeds and for
large gaps (>100 microns). There are no comprehensive data how very thin films, 20
microns and less (particularly lower limits in the region of 5 microns) can be
achieved at high speeds, of 2 or more metres per second. This study is concerned
precisely with this aim, that of investigating the effect of large speeds and small
roller gaps (rollers nearly touching or in elastohydrodynamic contact) to achieve the
very thin films desired by modern applications (electronics, medical and others). In
order to achieve this aim, a rig was designed and built to enable to understand the
effect of various coating conditions and liquid properties on the metered film
thickness and coating instability. To achieve thin films at high speeds, small roll gap
and low viscosity are needed, however flow instabilities will develop under these
conditions. To achieve stable coating window at high speeds high surface tension is
needed. It was found that the roll gap and the viscosity have complicated effect on
the coating window. In the case of low viscosity liquid (7mPa.s), small roll gaps are
needed, whereas in the case of high viscosity liquid (more than 30mPa.s), large gaps
are needed. It was found that Weber number is better describer for ribbing
instability in rigid reverse roll coating unlike in rigid forward roll coating in which
capillary number is the one.
In addition the potential of reverse deformable roll coating (rolls in
elastohydrodynamic contact) was investigated in order to achieve much thinner
films at higher speeds. As a result of the investigation of reverse deformable roll
coating, it was found that there is a possibility to get much thinner stable films at
much higher speeds compared to reverse rigid roll coating. The liquid transfer from an applicator roller to a PET film was investigated in
this study. It was found that air stagnation at downstream meniscus and air
entrainment at upstream meniscus depend on the liquid properties such as viscosity
and surface tension and coating conditions such as web tension and wrap angle of
web. As a result, wet film instability also depends on liquid properties and coating
conditions. It was found that air stagnation causes streaks on the wet film and air
entrainment caused bubbles on the wet film. To get a stable wet film, it was found
that suitable viscosity and high surface tension were needed. / TOYOBO
| Identifer | oai:union.ndltd.org:BRADFORD/oai:bradscholars.brad.ac.uk:10454/5753 |
| Date | January 2012 |
| Creators | Shibata, Yusuke |
| Contributors | Benkreira, Hadj, Patel, Rajnikant |
| Publisher | University of Bradford, School of Engineering, Design and Technology |
| Source Sets | Bradford Scholars |
| Language | English |
| Detected Language | English |
| Type | Thesis, doctoral, PhD |
| Rights | <a rel="license" href="http://creativecommons.org/licenses/by-nc-nd/3.0/"><img alt="Creative Commons License" style="border-width:0" src="http://i.creativecommons.org/l/by-nc-nd/3.0/88x31.png" /></a><br />The University of Bradford theses are licenced under a <a rel="license" href="http://creativecommons.org/licenses/by-nc-nd/3.0/">Creative Commons Licence</a>. |
Page generated in 0.0021 seconds