Structures deform at high strain rates and temperatures when exposed to impulsive loads. To accommodate the macro change there are microstructural changes that occur, i.e., grain morphology and shear banding. Most studies report on macroscopic response, i.e., large inelastic deformation and tearing of the structure, while limited studies have reported on microscopic changes that develop in the structure. The microstructure is directly related to the mechanical properties and performance of the material. Therefore, understanding the effect of high strain rate loadings on the microstructural evolution and subsequent mechanical properties of metals and alloys is necessary for mechanical design. The main objective of this research was to investigate microstructural changes to characterise the strain distribution and plastic deformation, owing to impulsive loading. Features within the microstructure that could be used to characterise deformation included grain size morphology changes, the presence of shear bands and sub-grain networks. The electron backscatter diffraction (EBSD) technique, which used Kikuchi patterns to characterise the strain distribution in the crystal of the deformed material, was also used as a characterisation tool. The first step in the experimental procedure was to select the appropriate material to investigate these microstructural changes. There was also the systematic investigation into the use of single and double heat treatments. These were used to achieve a large equiaxed grain structure, which was desirable from a microstructural point of view but was not desirable for blast-resistant material selection. The two-step heat treatment was concluded to be the most suitable heat treatment for the annealing and homogenisation of the AISI 430 stainless steel plates. The AISI 430 stainless steel plates used were 244 mm by 244 mm in size and had a circular exposed area of 106 mm. These plates were subjected to repeated explosive blasts, using a plastic explosive (PE4). The charge mass was varied for each test and the stand-off distance was kept constant at 150 mm for uniform loads and 13 mm for localised loads. Two plates were selected to investigate the uniform loading scenario. The first plate, a torn plate, used a charge mass of 30 g and one blast and the second plate, an inelastically-deformed plate, used a charge mass of 10 g and was exposed to three blasts. These two plates offered the same overall charge load with a different strain path. A further two plates were chosen for the investigation into the localised loading scenario. One plate, a petalled plate, used a 6 g charge mass and was exposed to two blasts and the second plate, an inelastically-deformed plate, used a 5 g charge mass and was also exposed to two blasts. The latter two plates offered an investigation into the effect of an increased charge load, where charge load affected the strain rate of the deformation resulting from the blast load. All four plates were sectioned across the midline of the dome and then ground and polished to a mirror finish, using OP-S. The polished samples were analysed, using optical microscopy and EBSD. In addition, Vickers hardness tests were carried out along the midline of the sectional plate profiles, in order to evaluate the extent of strain hardening. All the plates showed either a response of inelastically deforming or of complete or partial tearing failures when subjected to blast loads. For inelastic deformation failures, a global dome was characteristic of the uniform loading condition and an inner dome superimposed by the global dome was characteristic of the localised loading condition. Variation of charge mass and the number of blasts showed an increasing linear relationship between the impulse and midpoint deflection. The macrostructure showed a large variation of failures in the localised condition. The microstructural characterisation results produced micrographs showing regions of long, flat grains with multiple sub-grain networks, indicating deformed microstructures of the blast loaded plates. Parts of the microstructures displayed equiaxed/recrystallised grains characteristic of restoration processes, owing to high temperatures. Vickers hardness tests indicated an increase in material hardness as the number of blasts was increased, with a maximum hardness in the central region of the plates. In the first investigation, into uniform loading, the material characterisation results, combined with the fractography results, indicated brittle failure modes typical of high strain rate failures in strain rate sensitive materials, such as the chosen AISI 430 stainless steel plates. In the second investigation, into localised loading, the material characterisation results, combined with the fractography results, indicated a more ductile failure, owing to a 1 g incremental increase of charge mass, which confirmed the strain rate sensitivity of this material.
| Identifer | oai:union.ndltd.org:netd.ac.za/oai:union.ndltd.org:uct/oai:localhost:11427/27391 |
| Date | January 2017 |
| Creators | Shangase, Thobani Paul |
| Contributors | Yuen, Steeve Chung Kim, George, Sarah L |
| Publisher | University of Cape Town, Faculty of Engineering and the Built Environment, Blast Impact and Survivability Research Unit |
| Source Sets | South African National ETD Portal |
| Language | English |
| Detected Language | English |
| Type | Master Thesis, Masters, MSc (Eng) |
| Format | application/pdf |
Page generated in 0.016 seconds