Return to search

Zinc oxide TCOs (Transparent Conductive Oxides) and polycrystalline silicon thin-films for photovoltaic applications

Transparent conductive oxides (TCOs) and polycrystalline silicon (poly-Si) thin-films are very promising for application in photovoltaics. It is extremely challenging to develop cheap TCOs and poly-Si films to make photovoltaic devices. The aim of this thesis is to study sputtered aluminum-doped ZnO TCO and poly-Si films by solid-phase crystallization (SPC) for application in low-cost photovoltaics. The investigated aspects have been (i) to develop and characterize sputtered aluminum-doped ZnO (ZnO:Al) films that can be used as a TCO material on crystalline silicon solar cells, (ii) to explore the potential of the developed ZnO:Al films for application in ZnO:Al/c-Si heterojunction solar cells, (iii) to make and characterize poly-Si thin-films on different kinds of glass substrates by SPC using electron-beam evaporated amorphous silicon (a-Si) [referred to as EVA poly-Si material (SPC of evaporated a-Si)], and (iv) to fabricate EVA poly-Si thin-film solar cells on glass and improve the energy conversion efficiency of these cells by post-crystallization treatments. The ZnO:Al work in this thesis is focused on the correlation between film characteristics and deposition parameters, such as rf sputter power (Prf), working gas pressure (Pw), and substrate temperature (Tsub), to get a clear picture of film properties in the optimized conditions for application in photovoltaic devices. Especially the laterally non-uniform film properties resulting from the laterally inhomogeneous erosion of the target material are investigated in detail. The influence of Prf, Pw and Tsub on the structural, electrical, optical and surface morphology properties of ZnO:Al films is discussed. It is found that the lateral variations of the parameters of ZnO:Al films prepared by rf magnetron sputtering can be reduced to acceptable levels by optimising the deposition parameters. ZnO:Al/c-Si heterojunction solar cells are fabricated and characterized to demonstrate the feasibility of the fabricated ZnO:Al films for application in heterojunction solar cells. In this application, expensive indium-tin oxide (ITO) is usually used. Under the standard AM1.5G spectrum (100 mW/cm2, 25 ??C), the best fabricated cell shows an open-circuit voltage of 411 mV, a short-circuit current density of 30.0 mA/cm2, a fill factor of 66.7 %, and a conversion efficiency of 8.2 %. This is believed to be the highest stable efficiency ever reported for this type of cell. By means of dark forward current density-voltage-temperature (J-V-T) measurements, it is shown that the dominant current transport mechanism in the ZnO:Al/c-Si solar cells, in the intermediate forward bias voltage region, is trap-assisted multistep tunneling. EVA poly-Si thin-films are prepared on four types of glass substrates (planar and textured glass, both either bare or SiN-coated) based on evaporated Si, which is a cheaper Si deposition method than the existing technologies. The textured glass is realized by the UNSW-developed AIT process (AIT = aluminium-induced texture). The investigation is concentrated on finding optimized process parameters and evaluating film crystallization quality. It is found that EVA poly-Si films have a grain size in the range 0.8-1.5 ??m, and a preferential (111) orientation. UV reflectance and Raman spectroscopy measurements reveal a high crystalline material quality, both at the air-side surface and in the bulk. EVA cells are fabricated in both substrate and superstrate configuration. Special attention is paid to improving the Voc of the solar cells. For this purpose, after the SPC process, the samples receive the two post-crystallization treatments: (i) a rapid thermal anneal (RTA), and (ii) a plasma hydrogenation. It is found that two post-crystallization treatments more than double the 1-Sun Voc of the substrate-type cells. It is demonstrated that RTA improves the structural material quality of the cells. Furthermore, a hydrogenation step is shown to significantly improve the electronic material quality of the cells. Based on the RTA???d and hydrogenated EVA poly-Si material, the first mesa-type EVA cells are fabricated in substrate configuration, by using sputtered Al-doped ZnO as the transparent front contact. The investigation is focused on addressing the correlation between the type of the substrate and cell performance. Optical, electrical and photovoltaic properties of the devices are characterized. It is found that the performance of EVA cells depends on the glass substrate topography. For cells on textured glass, the AIT texture is shown to have a beneficial effect on the optical absorption of EVA films. It is demonstrated that a SiN barrier layer on the AIT-textured glass improves significantly both the crystalline quality of the poly-Si films and the energy conversion efficiency of the resulting solar cells. For cells on planar glass, a SiN film between the planar glass and the poly-Si film has no obvious effect on the cell properties. The investigations in this thesis clearly show that EVA poly-Si films are very promising for poly-Si thin-film solar cells on glass.

Identiferoai:union.ndltd.org:ADTP/257375
Date January 2005
CreatorsSong, Dengyuan, Centre for Photovoltaic Engineering, UNSW
PublisherAwarded by:University of New South Wales. Centre for Photovoltaic Engineering
Source SetsAustraliasian Digital Theses Program
LanguageEnglish
Detected LanguageEnglish
RightsCopyright Dengyuan Song, http://unsworks.unsw.edu.au/copyright

Page generated in 0.0016 seconds