Student Number : 0109917P -
PhD thesis -
School of Process and Materials Engineering -
Faculty of Engineering and the Built Environment / The aim of this project was to characterise new WC-10VC-Co powders, and to deposit WC-10VC-Co thermal spray coatings from these powders for characterisation and testing in adhesion, wear and corrosion tests. Throughout the project, the new powders and coatings were compared to commercial WC-Co powders of the same binder content and commercial WC-Co thermal spray coatings.
All the powders i.e WC-10VC-Co and WC-Co powders, were produced by agglomeration (by spray drying) and sintering and characaterised by determining the sizes and size distributions of the powders' particles, the morphology, the flowability and the phase composition and grain size and size distribution of carbide grains. The vanadium carbide in the WC-10VC-Co powders occurred in the solution as the double carbide (V,W)C and the carbides present in the WC-10VC-Co powders were WC and (V,W)C. None of the starting VC was left in the powders. Coatings were deposited using high pressure high velocity oxy-fuel (HP/HVOF) spraying systems, and characterized by determining the microstructures, the phase compositions and the carbide grain sizes, as had been done for the powders. Three types of tests were done on the coatings: adhesion tests, (according to standard SNECMA 14 -008); dry abrasion, wet abrasion and slurry erosion tests; and corrosion tests, in synthetic mione water.
Thermal spraying lead to some WC decarburization to W2C and eta phase, and to the formation of amorphous binder. The W2C grains from the WC decarburization formed in the amorphous binder matrix of coatings. All the coatinge were porous, but the new WC-10VC-Co coatings were more porous than the commercial Wc-Co coatings because the spray parameters had only been optimized for the WC-Co coatings. The carbide grains decreased in size by as much as 50% during decomposition. Evidence suggested that the WC grains in the coatings were subjected to different residual stresses that in the powders, probably due to the formation of the amorphous binder. Vanadium carbide in the Wc-10VC-Co coatings occurred as (V,W)C, just as in the powders, with as distribution that was reasonably homogeneous. The apparent hardness of the new Wc-10VC-Co coatings was slightly lower than that of WC-Co coatings of the same cobalt content, due to their higher porosity.
The adhesion of the new Wc-10VC-Co coatings was as good as that of the Wc-Co coatings. The dry and wet abrasion resistance of the new Wc-10VC-Co coatings was better that for the Wc-Co coatings of equal Co wt%, on account of the Wc-10VC-Co coatings having a lower binder volume fraction, finer carbide grains, and (V,W)C grains. The (V,W)C grains are harder than WC grains and apparently slowed down the overall abrasion rate. In slurry erosion, the best performance of the Wc-10VC-Co coatings was as good as that of the commercial WC-Co coatings at equal cobalt mass content, due to the higher porosity of the Wc-10VC-Co coatings, apparent faster erosion of the harder but brittle (V,W)C grains, and, from what evidence appreared to suggest, generally slightly poorer erosion resistance of the fine WC grains under the test conditions used. Polishing the slurry erosion test specimens reduced mass losses in slurry erosion by factor of up to 10 compared to the unpolished specimens, and led to better erosion resistance of the WC-10VC-Co coating compared to the WC-12Co coating.
The results of the tests done to investigate the corrosion properties of the coatings were conclusive. This is because the effects of cleaning procedures on mass loss after immersion corrosion were not explored, and it appeared, for some coatings, that the corrosion mechanisms in immersion corrosion could not be reproduced in electrochemical testing.
| Identifer | oai:union.ndltd.org:netd.ac.za/oai:union.ndltd.org:wits/oai:wiredspace.wits.ac.za:10539/1827 |
| Date | 17 November 2006 |
| Creators | Machio, Christopher Nyongesa |
| Source Sets | South African National ETD Portal |
| Language | English |
| Detected Language | English |
| Type | Thesis |
| Format | 149152503 bytes, application/pdf, application/pdf |
Page generated in 0.0015 seconds