Return to search

Isotope ratios in source determination of formaldehyde emissions

Formaldehyde emissions from non-structural wood composites are regulated and the regulation target is urea-formaldehyde (UF) resin. UF resins are hydrolytically unstable and constantly emit formaldehyde as a function of temperature and relative humidity. When heated, wood also generates formaldehyde, but this was of little concern until 2010 when formaldehyde regulations became much more demanding. This regulation motivated the industry to account for all formaldehyde sources, synthetic as from resin, and biogenic as from wood. This effort represents first steps towards quantifying biogenic and synthetic contributions to formaldehyde emissions in non-structural wood composites.

It is possible to distinguish the 13C/12C isotope ratio of UF resins from the isotope ratio of plant biomass. Conditions during and after composite hot-pressing promote reactions that generate formaldehyde from wood and UF resin, and the kinetic isotope effect continuously lowers the product isotope ratios as a function of yield. If such isotope fractionation did not occur, it would be a simple matter to quantify contributions of wood and UF resin to formaldehyde emissions using static isotope ratios. Isotope fractionation, therefore, complicates the requirements for distinguishing biogenic and synthetic formaldehyde in wood composite emissions. Those requirements are 1) establish the reference carbon isotope ratios in wood and in UF resin (just the formaldehyde portion of UF), and 2) estimate the kinetic isotope effects in formaldehyde generation by wood and cured UF resin. The latter requirement fixes a range for the respective isotope ratios; the numerical ranges enable a simple model of the average isotope ratio for a mixture of biogenic and synthetic formaldehyde in wood composite emissions. Finally, the measured isotope ratio of captured emissions would be compared to the model.

This work did not achieve all aspects of the requirements mentioned, but a solid foundation was established for future completion of the ultimate goals. In reference to requirement 1, the carbon isotope ratio of experimental Pinus taeda wood was accurately measured (including some isolated fractions) using isotope ratio mass spectroscopy (IRMS). IRMS of UF resin first requires removal of urea carbons- UF resin was subjected to acid hydrolysis and capture of the resin formaldehyde into aqueous ammonium hydroxide. This provided a nearly quantitative conversion (negligible isotope fractionation) of resin formaldehyde into hexamine for IRMS. Using this hexamine method, the formaldehyde carbon isotope ratios of two industrial UF resins were accurately measured, demonstrating basic feasibility for the project goal.

Estimating the kinetic isotope effect (Requirement 2) required creation of a thermochemical reactor, where wood or cured UF resin was heated under N2 flow such that the emitted formaldehyde was easily captured. In this case, conversion of captured formaldehyde into hexamine was abandoned in favor of silica gel cartridges loaded with sodium bisulfite. Isolation and IRMS of the formaldehyde-bisulfite adduct were effective and considered easily transferable to industrial settings. This system was employed to measure fractionation in cured resin as a function of relative humidity, and in Pinus taeda wood as a function of relative humidity, temperature, and time. More information about isotope fractionation is required; but most notable was the fractionation behavior in wood where evidence was found for multiple formaldehyde generating reactions. Overall, this work established feasibility for the goals and laid the foundation for future efforts. / Master of Science / Home-interior products like cabinetry are often produced with wood composites adhesively bonded with urea-formaldehyde (UF) resin. UF resins are low cost and highly effective, but their chemical nature results in formaldehyde emission from the composite. High emissions are avoided, and the federal government has regulated and steadily reduced allowable emissions since 1985. The industry continuously improved UF technologies to meet regulations, as in 2010 when the most demanding regulations were implemented. At that time, many people were unaware that wood also generates formaldehyde; this occurs at very low levels but heating during composite manufacture causes a temporary burst of natural formaldehyde. Some wood types produce unusually high formaldehyde levels, making regulation compliance more difficult. This situation, and the desire to raise public awareness, created a major industrial goal: determine how much formaldehyde emission originates from the resin and how much originates from the wood. These formaldehyde sources can be distinguished by measuring the carbon isotope ratio, 13C/12C. This ratio changes and varies due to the kinetic isotope effect. Slight differences in 13C and 12C reactivity reveal the source as either petrochemical (synthetic formaldehyde) or plant-based (biogenic formaldehyde). This work demonstrates that achieving the industry goal is entirely feasible, and it provides the analytical foundation.

The technical strategy is: 1) establish reference isotope ratios in wood and in UF resin, and 2) from the corresponding wood composite, capture formaldehyde emissions, measure the isotope ratio, and simply calculate the percentage contributions from the reference sources. However, a complication exists. When the reference sources generate formaldehyde, the respective isotope ratios change systematically in a process called isotope fractionation (another term for the kinetic isotope effect). Consequently, this effort developed methods to measure fractionation when cured UF resin and wood separately generate formaldehyde, with greater emphasis on wood. Isotope fractionation in wood revealed multiple fractionation mechanisms. This complexity presents intriguing possibilities for new perspectives on formaldehyde emission from wood and cured UF resin. In summary, this work demonstrated how source contributions to formaldehyde emissions can be determined; it established effective methods required to refine and perfect the approach, and it revealed that isotope fractionation could serve as an entirely novel tool in the materials science of wood composites.

Identiferoai:union.ndltd.org:VTETD/oai:vtechworks.lib.vt.edu:10919/99308
Date08 July 2020
CreatorsYousefi-Shivyari, Niloofar
ContributorsChemistry, Frazier, Charles E., Strahm, Brian D., Edgar, Kevin J.
PublisherVirginia Tech
Source SetsVirginia Tech Theses and Dissertation
Detected LanguageEnglish
TypeThesis
FormatETD, application/pdf
RightsIn Copyright, http://rightsstatements.org/vocab/InC/1.0/

Page generated in 0.0029 seconds