In this research, the effects of gas composition, elapsed time of reaction and temperature on scale formation and descaling of low carbon steel were investigated and results were discussed from the viewpoint of the phase composition of the scales, oxidation rates, oxidation mechanisms, adhesion, fracture mechanics, porosity and residual scale. / The phase composition and morphology of scales grown under conditions similar to those of reheating furnaces were analyzed. Low carbon steel was oxidized over the temperature range 1000-1250°C in gas mixtures of O 2-CO2-H2O-N2, O2-H 2O-N2 and O2-CO2-N2. The mole fraction of each phase, wustite (FeO), magnetite (Fe3O 4) and hematite (Fe2O3) was determined by the direct comparison method Two types of scales were observed. The first type was a crystalline scale with an irregular outer surface composed mostly of wustite, and a negligible amount of magnetite. The second type was the classical three-layer scale composed of wustite, magnetite and hematite. In general, the experiments showed that the furnace atmosphere, oxidation time and temperature influence the phase composition of the scales. / Low carbon steel was oxidized in air over the temperature range 600-1200°C for 120 s to approximate the formation of secondary and tertiary scale in hot rolling. The mole fraction of wustite, magnetite and hematite was determined by the direct comparison method The phase composition of the scales changed with temperature and time. During the initial 30 s of oxidation, wustite was the predominant phase in the temperature range 800-1200°C, and as oxidation proceeded, the percentages of magnetite and hematite increased. In addition, the texture of the scales was investigated by orientation imaging microscopy (OIM); it was found that temperature influences the texture of the scales. The experiments indicated that 850°C is the ideal temperature for the finishing mill in order to reduce surface defects and work roll wear. / The adhesion of scales formed in air on low carbon steel in continuous heating and isothermal conditions was investigated with a four-point bending test. The separation (crack) always occurred inside the scale indicating that the strength of the scale is lower than the strength of the scale/steel interface. It was found that scale adhesion is related to scale porosity, blister formation and stresses acting in the scale. A spallation process was observed when cooling from 800°C to room temperature. The microscopic observations revealed that spallation followed route 1 "strong interface and weak oxide." / Low carbon steel was oxidized over the temperature range 1050-1250°C in O2-CO2H2O-N2 gas mixtures in order to study the hydraulic descaling process. The oxidation times were 15-120 min. and the scales were 130-2000 mum thick. The experimental parameters were chosen to approximate scale formation under conditions similar to those of reheating furnaces. In the hydraulic descaling tests, two modes of scale removal were observed. In the first mode, observed in classical three-layer scales that developed an inner porous layer with low or medium porosity, the horizontal undercutting occurred at the boundary of the inner porous layer and dense scale. The second mode was observed in classical three-layer scales that developed an inner porous layer with high porosity and in crystalline scales. In the second mode, the horizontal undercutting occurred at the first plane of large pores relative to the scale/steel interface. In general, the experiments showed that scale morphology controlled the removability of scale.
| Identifer | oai:union.ndltd.org:LACETR/oai:collectionscanada.gc.ca:QMM.115671 |
| Date | January 2008 |
| Creators | Basabe Mancheno, Vladimir Vinicio, 1968- |
| Publisher | McGill University |
| Source Sets | Library and Archives Canada ETDs Repository / Centre d'archives des thèses électroniques de Bibliothèque et Archives Canada |
| Language | English |
| Detected Language | English |
| Type | Electronic Thesis or Dissertation |
| Format | application/pdf |
| Coverage | Doctor of Philosophy (Department of Mining and Materials Engineering.) |
| Rights | All items in eScholarship@McGill are protected by copyright with all rights reserved unless otherwise indicated. |
| Relation | alephsysno: 003164479, proquestno: AAINR66289, Theses scanned by UMI/ProQuest. |
Page generated in 0.0015 seconds