Return to search

An experimental investigation of the flow around impulsively started cylinders

A study of impulsively started flow over cylindrical objects is made using the particle image velocimetry (PIV) technique for Reynolds numbers of Re = 200, 500 and 1000 in an X-Y towing tank. The cylindrical objects studied were a circular cylinder of diameter, D = 25.4 mm, and square and diamond cylinders each with side length, D = 25.4 mm. The aspect ratio, AR (= L/D) of the cylinders was 28 and therefore they were considered infinite. The development of the recirculation zone up to a dimensionless time of t* = 4 following the start of the motion was examined. The impulsive start was approximated using a dimensionless acceleration parameter, a*, and in this research, the experiments were conducted for five acceleration parameters, a* = 0.5, 1, 3, 5 and 10. The study showed that conditions similar to impulsively started motion were attained once a* ¡Ý 3.<p>
A recirculation zone was formed immediately after the start of motion as a result of flow separation at the surface of the cylinder. It contained a pair of primary eddies, which in the initial stages (like in this case) were symmetrical and rotating in opposite directions. The recirculation zone was quantified by looking at the length of the zone, LR, the vortex development, both in terms of the streamwise location and the cross-stream spacing of the vortex centers, a and b, respectively, as well as the circulation (strength) of the primary vortices, ¦£.<p>
For all types of cylinders examined, the length of the recirculation zone, the streamwise location of the primary eddies and the circulation of the primary eddies increase as time advances from the start of the impulsive motion. They also increase with an increase in the acceleration parameter, a*, until a* = 3, beyond which there is no more change, since the conditions similar to impulsively started conditions have been achieved. The cross-stream spacing of the primary vortices is relatively independent of Re, a* and t* but was different for different cylinders.<p>
Irrespective of the type of cylinder, the growth of the recirculation zone at Re = 500 and 1000 is smaller than at Re = 200. The recirculation zone of a diamond cylinder is much larger than for both square and circular cylinders. The square and diamond cylinders have sharp edges which act as fixed separation points. Therefore, the cross-stream spacing of the primary vortex centers are independent of Re, unlike the circular cylinder which shows some slight variation with changes in Reynolds number.<p>
The growth of the recirculation is more dependent on the distance moved following the start of the impulsive motion; that is why for all types of cylinders, the LR/D, a/D and ¦£/UD profiles collapse onto common curves when plotted against the distance moved from the start of the motion.

Identiferoai:union.ndltd.org:LACETR/oai:collectionscanada.gc.ca:SSU.etd-08252009-124243
Date10 September 2009
CreatorsTonui, Nelson Kiplanga't
ContributorsSumner, David
PublisherUniversity of Saskatchewan
Source SetsLibrary and Archives Canada ETDs Repository / Centre d'archives des thèses électroniques de Bibliothèque et Archives Canada
LanguageEnglish
Detected LanguageEnglish
Typetext
Formatapplication/pdf
Sourcehttp://library.usask.ca/theses/available/etd-08252009-124243/
Rightsrestricted, I hereby certify that, if appropriate, I have obtained and attached hereto a written permission statement from the owner(s) of each third party copyrighted matter to be included in my thesis, dissertation, or project report, allowing distribution as specified below. I certify that the version I submitted is the same as that approved by my advisory committee. I hereby grant to University of Saskatchewan or its agents the non-exclusive license to archive and make accessible, under the conditions specified below, my thesis, dissertation, or project report in whole or in part in all forms of media, now or hereafter known. I retain all other ownership rights to the copyright of the thesis, dissertation or project report. I also retain the right to use in future works (such as articles or books) all or part of this thesis, dissertation, or project report.

Page generated in 0.0019 seconds