The coagulation/flocculation process is an important part of surface water treatment. It has direct impact on the reliability of plant operations and final water qualities together with cost control. Low water temperature has a significant impact on the operation of drinking water treatment plants, especially on coagulation/flocculation processes.<p> A microscopic image technique has been used to study the coagulation and flocculation process in recent years, but it requires sample handling that disturbs the floc characteristics during measurement. A high resolution photographic technique was applied to evaluate flocculation processes in the present work. With this technique, the images of the flocs were obtained directly while the flocculation process was taking place. In combination with camera control software and particle size analysis software, this procedure provided a convenient means of gathering data to calculate size distribution. Once the size distribution was calculated, the floc growth and floc size change in the aggregation process could be analyzed. Results show that low water temperature had a detrimental impact on aggregation processes. A water temperature of 0 °C resulted in a slow floc growth and small floc size. Although the floc growth rates at 4 °C and 1 °C were less than those at 22 °C, they were higher than at 0 °C. To improve aggregation processes at low water temperature, adding the coagulant aid of anionic copolymer of acrylamide into the water was found to be effective when the temperature was not less than 1 °C. However, it made only a slight impact on aggregation when the temperature approached 0 °C. At water temperatures of 22 °C, 4 °C and 1 °C, the polymer caused the formation of large floc (larger than 0.5 mm2 in projected area). The polymer significantly shortened the required time of flocculation and sedimentation. Three minutes of flocculation and 20 minutes of sedimentation were sufficient for the polymer to achieve good treatment performance, while the flocculation time and sedimentation time had to be 20 and 60 minutes, respectively, without using the polymer. On the other hand, when the temperature was close to 0 °C, the polymer did not cause the formation of the large floc, nor did it shorten the time of flocculation and sedimentation.<p> The experimental results in this research agree with the model for flocculation kinetics given by Argaman and Kaufman (1970). With decreasing water temperature, the aggregation constant (KA) decreased and breakup constant (KB) increased. KA and KB with aluminum sulfate was close to those with ferric sulfate, respectively. <p> In treating the South Saskatchewan River water, an aluminum sulfate or ferric sulfate dosage greater than 50 mg/L resulted in marginal gains in treatment efficiency. Decreasing dosages of aluminum sulfate or ferric sulfate caused lower floc growth rates and smaller floc sizes. Extremely low dosages (5 mg/L or less) resulted in poor floc formation and extremely small sizes.
| Identifer | oai:union.ndltd.org:LACETR/oai:collectionscanada.gc.ca:SSU.etd-06042005-213443 |
| Date | 06 June 2005 |
| Creators | Jin, Yan |
| Contributors | Sparling, Bruce F., Peng, Jian |
| Publisher | University of Saskatchewan |
| Source Sets | Library and Archives Canada ETDs Repository / Centre d'archives des thèses électroniques de Bibliothèque et Archives Canada |
| Language | English |
| Detected Language | English |
| Type | text |
| Format | application/pdf |
| Source | http://library.usask.ca/theses/available/etd-06042005-213443/ |
| Rights | unrestricted, I hereby certify that, if appropriate, I have obtained and attached hereto a written permission statement from the owner(s) of each third party copyrighted matter to be included in my thesis, dissertation, or project report, allowing distribution as specified below. I certify that the version I submitted is the same as that approved by my advisory committee. I hereby grant to University of Saskatchewan or its agents the non-exclusive license to archive and make accessible, under the conditions specified below, my thesis, dissertation, or project report in whole or in part in all forms of media, now or hereafter known. I retain all other ownership rights to the copyright of the thesis, dissertation or project report. I also retain the right to use in future works (such as articles or books) all or part of this thesis, dissertation, or project report. |
Page generated in 0.0024 seconds