In the last decades, intensive research has been carried out in order to replace oil-based polymers with bio-based polymers due to growing environmental concerns. So far, most of the barrier materials used in food packaging are petroleum-based materials. The purpose of the barrier is to protect the packaged food from oxygen, water vapour, water and fat. The mechanical and barrier properties of coatings based on starch-plasticizer and starch-poly(vinyl alcohol) (PVOH)-plasticizer blends have been studied in the work described in this thesis. The plasticizers used were glycerol, polyethylene glycol and citric acid. In a second step, polyethylene coatings were extruded onto paperboard pre-coated with a starch-PVOH-plasticizer blend. The addition of PVOH to the starch increased the flexibility of the film. Curing of the film led to a decrease in flexibility and an increase in tensile strength. The flexibility of the starch-PVOH films was increased more when glycerol or polyethylene glycol was added than citric acid. The storage modulus of the starch-PVOH films containing citric acid increased substantially at high temperature. It was seen that the addition of polyethylene glycol or citric acid to the starch-PVOH blend resulted in an enrichment of PVOH at the surface of the films. Tensile tests on the films indicated that citric acid acted as a compatibilizer and increased the compatibility of the starch and PVOH in the blend. The addition of citric acid to the coating recipe substantially decreased the water vapour transmission rate through the starch-PVOH coated paperboard, which indicated that citric acid acts as a cross-linker for starch and/or PVOH. The starch-PVOH coatings containing citric acid showed oxygen-barrier properties similar to those of pure PVOH or of a starch-PVOH blend without plasticizer when four coating layers were applied on a paperboard. The oxygen-barrier properties of coatings based on a starch-PVOH blend containing citric acid indicated a cross-linking and increase in compatibility of the starch-PVOH blends. Polyethylene extrusion coating on a pre-coated paperboard resulted in a clear reduction in the oxygen transmission rate for all the pre-coating formulations containing plasticizers. The addition of a plasticizer to the pre-coating reduced the adhesion of polyethylene to pre-coated board. Polyethylene extrusion coating gave a board with a lower oxygen transmission rate when the paperboard was pre-coated with a polyethylene-glycol-containing formulation than with a citric-acid-containing formulation. The addition of polyethylene glycol to pre-coatings indicated an increase in wetting of the pre-coated paperboard by the polyethylene melt, and this may have sealed the small defects in the pre-coating leading to low oxygen transmission rate. The increase in brittleness of starch-PVOH films containing citric acid at a high temperature seemed to have a dominating effect on the barrier properties developed by the extrusion coating process. / Over the last few decades, industry and academia have made joint efforts to generate knowledge about renewable barrier materials in order to replace the oil-based barrier materials currently used in food packaging. This work has focused on the possibility of producing a material with high oxygen barrier properties including polyethylene as a moisture protection. The flexibility of starch films was increased by adding poly(vinyl alcohol) (PVOH) to the starch and the addition of a plasticizer to the starch-PVOH blend films further increase the flexibility of the films. The plasticizers used were glycerol, polyethylene glycol and citric acid. Curing of the films reduce their flexibility. The addition of citric acid to a starch-PVOH blend increased the compatibility of the starch-PVOH blend and affected the barrier properties of the coating layers containing citric acid. When a sufficient number of coating layers was applied, the starch-PVOH-citric-acid coatings showed oxygen-transmission-rate-values similar to those of the pure PVOH and of the starch-PVOH blend without plasticizers. Polyethylene extrusion coating on pre-coated paperboard resulted in a clear reduction in the oxygen transmission rate of all the pre-coating recipes based on starch-PVOH blends. The polyethylene extrusion coating showed a higher oxygen transmission rate for a board pre-coated with citric-acid-containing recipes than for a board pre-coated with polyethylene-glycol-containing recipes.
| Identifer | oai:union.ndltd.org:UPSALLA1/oai:DiVA.org:kau-38337 |
| Date | January 2015 |
| Creators | Javed, Asif |
| Publisher | Karlstads universitet, Institutionen för ingenjörs- och kemivetenskaper (from 2013), Karlstad University, Karlstad |
| Source Sets | DiVA Archive at Upsalla University |
| Language | English |
| Detected Language | English |
| Type | Licentiate thesis, comprehensive summary, info:eu-repo/semantics/masterThesis, text |
| Format | application/pdf |
| Rights | info:eu-repo/semantics/openAccess |
| Relation | Karlstad University Studies, 1403-8099 ; 2015:54 |
Page generated in 0.0026 seconds