Soldering results from the interfacial interactions between the die and the casting alloy during high pressure die casting and is one of the major die failure modes. To prevent this occurring, lubricant layers and surface coatings are used to act as a barrier between the die and the casting alloy. The microstructures of a series of soldered layers on H13 tool steel core pins were examined after conducting high pressure die casting experiments with a specially designed die using removable core pins and Al-11Si-3Cu casting alloy. This showed that first, a casting alloy build-up layer formed, and then intermetallic phases nucleated at the die steel interface and grew to cover the entire surface in subsequent casting cycles. The structures of intermetallic layers formed during immersion of H13 tool steel into an Al-11Si-3Cu casting alloy melt were studied by X-ray diffraction and energy dispersive spectroscopy (EDS). A thick composite layer away from the H13 steel substrate consisted of irregular intermetallic phases and solidified casting alloy. A thin intermetallic layer was present between the composite layer and an inner compact layer next to the steel substrate. The irregular intermetallic phase in the thick composite layer away from the H13 steel substrate was identified to have a body centre cubic (bcc) structure, abcc-( FeSiAlCrMnCu). The thin and continuous intermetallic layer between the composite layer and the inner compact layer was found to be structurally isomorphous with aH-Fe2SiAl8. The compositional differences observed between aH and abcc phases indicated that the latter consisted of a higher amount of chromium, manganese, copper, and a lower amount of iron. It was likely that the presence of chromium, manganese and copper in the H13 tool steel caused the transformation of aH®abcc. The inner compact layer next to the steel substrate was identified to be orthorhombic h-Fe2Al5 containing silicon and chromium. An examination of lubricants to prevent soldering in high pressure die casting in conjunction with Nissan Casting Australia Pty Ltd. found that soldering was reduced by using a suitable lubricant. The chemistry of the lubricant, spray parameters, and die surface temperature were important factors in producing a protective lubricant layer. It was found that lubricant containing polypropylene waxes prevented soldering significantly better than lubricant containing polyethylene waxes. It was also found that the lubricant containing polypropylene waxes had lower surface tension. An examination of the use of iron oxide layers to prevent soldering in high pressure die casting was performed. H13 tool steel was oxidised in air and produced porous iron oxide with a mixture of haematite (Fe2O3) and magnetite (Fe3O4). These porous iron oxides did not completely prevent the H13 steel from soldering in immersion tests as intermetallic cones formed at the surface of the steel. Commercial steam tempering of H13 steel produced more compact iron oxide layers with magnetite (Fe3O4) and haematite (Fe2O3) structures. It was found that these compact iron oxide layers offered better protection against soldering than the porous layers created in air. Pure iron oxidised in a CO2/H2 gas mixture at a ratio of 95:5 at 550°C produced structurally pure, compact magnetite (Fe3O4) layers. H13 steel oxidised in a CO2/H2 gas mixture at a ratio of 95:5 at 550°C produced compact iron oxide layers that showed only magnetite (Fe3O4) structure. The magnetite (Fe3O4) layer containing chromium, manganese, silicon and vanadium formed next to the H13 substrate was found to be a very adherent layer and protected H13 steel from soldering in high pressure die casting experiments with a specially designed die using removable core pins and Al-11Si-3Cu casting alloy. An examination of aluminium oxide layers to prevent soldering in high pressure die casting was performed. Incoloy MA956 containing 4.5 wt.% aluminium, oxidised in air at 1100°C, produced a single, compact, adherent oxide layer with a-alumina (Al2O3) structure, that prevented the formation of intermetallic phases between aluminium alloy and Incoloy MA956 during high pressure die casting. However, non-reactive casting alloy build-up formed on the oxide coatings, similarly to physical vapour deposition (PVD) and vanadium carbide coatings. It was found that the thickness of the non-reactive casting alloy build-up was reduced by decreasing the roughness of the oxide coatings by lightly grinding of the surface of the coatings. The industrial application of these findings are discussed and directions for further research are presented.
| Identifer | oai:union.ndltd.org:ADTP/253778 |
| Creators | Fraser, Darren Timothy |
| Source Sets | Australiasian Digital Theses Program |
| Detected Language | English |
Page generated in 0.0012 seconds