For grafting polypyrrole on oxidized surfaces, 3-substituted pyrrole alkyl phosphonic acids, 11-(pyrrol-3-yl undecyl) trimethoxysilanes and 1-substituted pyrrole alkyl organosilanes with different chain length were designed and successfully synthesized as adhesion promoters. These new derivatives were studied for their adsorption behavior on oxide substrates and chemical or electrochemical deposition of polypyrrole over modified oxide surface or electrodes. Several analytical techniques such as contact angle measurement, surface plasmon resonance spectroscopy (SPR), UV-VIS Spectroscopy, grazing incident FTIR, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM) were employed to characterize the adsorbed layers on different substrates. Contact angle measurement and ellipsometry data showed that high concentrations in apolar hydrocarbon solvent and long reaction times are sufficient to form tightly packed monolayer of 1-substituted pyrrole alkyl monochlorosilanes (PMCS) on substrates. Adsorption kinetics were studied by SPR and showed that the adsorption took place within a few seconds, then continuously increased and reached a plateau. The orientation of these synthesized monomers is investigated to be well-suited for use as adhesion promoter. CV-measurements showed that 3-substrated pyrrole derivatives had lower oxidation potential, whereas 1-substituted pyrrole derivatives had higher oxidation potential compared with pyrrole. Surface deposition of polypyrrole on the adhesion promoter modified (silane-modified and phosphonic acid-modified) substrates by chemical and electrochemical polymerization were investigated. PPy films formed on the modified surfaces by surface chemical polymerization showed a better adhesion compared to those on the unmodified surfaces. The morphology of PPy films was influenced by the alkyl chain length of the adhesion promoter and the deposition condition, such as choice of oxidant and solvent. The thickness of the resulting PPy films were controlled by the polymerization conditions, such as choice of solvent, deposition time, pyrrole to oxidant ratio and monomer concentration. The thickness of the deposited PPy film was estimated in the range of 10-400 nm by AFM and ellipsometry. The electrical properties were studied by current-voltage (j-V) measurement. Temperature dependence of j-V characteristics of Si/SiO2/PPy/PMCS-16/Al films revealed that the current increases with temperature, the film shows a typical semiconductor behavior. The use of these adhesion promoters modified electrode for electrochemical polymerization resulted in adhesive polypyrrole films.Also the 3-substituted pyrrole phosphonic acids were found to be homo-and co-polymerizable (with pyrrole) under chemical methods. TGA showed that homopolymers are less stable than polypyrrole due to the 3-substitution. he homopolymer of 3-substituted phosphonic acid derivatives of pyrrole is soluble. Films coated from the MeOH solution of homopolymer could be successfully used as humidity sensors. It is observed that the resistivity of the 3-substituted homopolypyrrole sensors increases and capacitance decreases during exposure to humid air. The polypyrrole films obtained by surface chemical polymerization was also used as humidity sensors.
Identifer | oai:union.ndltd.org:DRESDEN/oai:qucosa.de:swb:14-1109334028224-37122 |
Date | 24 January 2005 |
Creators | Cai, Xuediao |
Contributors | Technische Universität Dresden, Mathematik und Naturwissenschaften, Chemie, Insitut für Makromolekulare Chemie und Textilchemie, Prof. Dr. rer. nat. Hans-Jürgen Adler, Prof. RNDr. ; Dr. sc. Stanislav Nespurek, Prof. Dr. rer. nat. Brigitte Voit, Prof. Dr. rer. nat. Hans-Jürgen Adler |
Publisher | Saechsische Landesbibliothek- Staats- und Universitaetsbibliothek Dresden |
Source Sets | Hochschulschriftenserver (HSSS) der SLUB Dresden |
Language | English |
Detected Language | English |
Type | doc-type:doctoralThesis |
Format | application/pdf |
Page generated in 0.0021 seconds