Orientador: Amauri Hassui / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecânica / Made available in DSpace on 2018-08-21T02:22:26Z (GMT). No. of bitstreams: 1
Aguiar_HerbertCesarGoncalvesde_M.pdf: 11222250 bytes, checksum: a22406ca3de132e13522314dd3490816 (MD5)
Previous issue date: 2012 / Resumo: Os aços inoxidáveis superduplex são materiais de estrutura bifásica contendo ferrita e austenita, que garantem ao material boa resistência à corrosão por pitting, resistência mecânica e outras características que tornam o material atrativo para as indústrias: petrolífera, óleo/gás, papel/ celulose e química. As mesmas características que tornam o aço inoxidável superduplex mais resistente dificultam a sua usinagem. Portanto, a definição dos parâmetros de usinagem deve atender ao compromisso de por um lado garantir alta produtividade e por outro não comprometer as características do material na sua aplicação. O presente trabalho consiste no torneamento com lubrificação do aço inoxidável superduplex, variando os parâmetros de usinagem e utilizando ferramentas de metal duro da classe M05-M20 revestidas com TiN/Al2O3/TiCN, Al2O3/TiCN e TiAlN, com o objetivo de investigar os efeitos dos parâmetros de usinagem sobre o mecanismo de desgaste da ferramenta através de micrografias obtidas por microscopia eletrônica de varredura (MEV) e de micro-análise semi-quantitativa através do sistema de espectroscopia de energia dispersiva (EDS), a tensão residual induzida no material usinado medida por difração raio-X e a rugosidade na peça. As análises do desgaste da ferramenta mostraram a predominância do mecanismo de adesão/attrition com surgimento de entalhe causado pelo martelamento da rebarba gerada no cavaco durante o torneamento. Isso por sua vez contribuiu ainda mais com a adesão dificultando a remoção do material que aumentou os esforços de corte gerando tensões residuais superficiais compressivas. A ferramenta revestida com TiN/Al2O3/TiCN se destacou por apresentar melhor resultado em termos de vida da ferramenta e menores tensões residuais superficiais de tração no início de vida da ferramenta em relação às ferramentas revestidas com TiAlN e Al2O3/TiCN. A condição de vc = 80 m/min e f = 0,4 mm/rev se destacou dentre todas as classes testadas em termos de produtividade. No entanto, o f = 0,4 mm/rev é prejudicial à integridade superficial gerando tensões trativas e maiores rugosidades / Abstract: The super duplex stainless steels are materials of biphasic structure containing ferrite and austenite, which guarantee a good pitting corrosion resistance, mechanical resistance and other characteristics that make the material attractive to industries: petroleum, oil/gas, paper/cellulose and chemical. The same characteristics that make the super duplex stainless steel more resistant make its machining more difficult. Therefore, the definition of machining parameters should comply with the commitment on the one hand of guaranteeing high productivity and on the other of not compromising the characteristics of the material in its application. This work consists on the turning with lubrication of the super duplex stainless steel, varying the machining parameters and using carbide tools of the grade M05-M20 coated with TiN/Al2O3/TiCN, TiAlN and Al2O3/TiCN, with the objective of investigating the effects of the machining parameters over the tools wear mechanism was also analyzed through micrographs obtained by scanning electron microscopy (SEM) and by semi-quantitative micro-analysis through the system energy dispersive spectroscopy (EDS), the residual stress induced into machined material measured by X-ray diffraction and the parts roughness. The tool wear analysis showed a predominance of the adherence/attrition mechanism with the appearance of grooves caused by the hammering of the burr generated in the chip during the turning. This, in its turn, contributed even more with the adhesion, making it difficult to remove the material which increased the effort in cutting, generating superficial compressive residual stress. The tool coated with TiN/Al2O3/TiCN highlighted itself for presenting better result in terms of the life of the tool and lower surface residual stresses of tensile at the beginning of tool life in relation to the tools coated with TiAlN and Al2O3/TiCN. The condition of vc = 80 m/min and f = 0,4 mm/rev highlighted itself among all the tested classes in terms of productivity. However, the f = 0,4 mm/rev is prejudicial to the superficial integrity, generating tensile stress and greater roughness / Mestrado / Materiais e Processos de Fabricação / Mestre em Engenharia Mecânica
Identifer | oai:union.ndltd.org:IBICT/oai:repositorio.unicamp.br:REPOSIP/264548 |
Date | 21 August 2018 |
Creators | Aguiar, Herbert César Gonçalves de |
Contributors | UNIVERSIDADE ESTADUAL DE CAMPINAS, Hassui, Amauri, 1967-, Diniz, Anselmo Eduardo, Abrão, Alexandre Mendes |
Publisher | [s.n.], Universidade Estadual de Campinas. Faculdade de Engenharia Mecânica, Programa de Pós-Graduação em Engenharia Mecânica |
Source Sets | IBICT Brazilian ETDs |
Language | Portuguese |
Detected Language | English |
Type | info:eu-repo/semantics/publishedVersion, info:eu-repo/semantics/masterThesis |
Format | 111 p. : il., application/pdf |
Source | reponame:Repositório Institucional da Unicamp, instname:Universidade Estadual de Campinas, instacron:UNICAMP |
Rights | info:eu-repo/semantics/openAccess |
Page generated in 0.0018 seconds