As a clean, abundant, and renewable source of energy with a strategic location in close proximity to global population regions, ocean wave energy shows major promise. Although much wave energy converter development has focused on large-scale power generation, there is also increasing interest in small-scale applications for powering the blue economy. In this thesis, the objective was to optimize the performance of small-sized, portable, oscillating-body wave energy converters (WECs). Two types of oscillating body WECs were studied: bottom hinged and two-body attenuator. For the bottom-hinged device, the goal was to show the feasibility of an oscillating surge WEC and desalination system using numerical modeling to estimate the system performance. For a 5-day test period, the model estimated 517 L of freshwater production with 711 ppm concentration and showed effective brine discharge, agreeing well with preliminary experimental results.
The objective for the two-body attenuator was to develop a method of power maximization through resonance tuning and numerical simulation. Three different geometries of body cross sections were used for the study with four different drag coefficients for each geometry. Power generation was maximized by adjusting body dimensions to match the natural frequency with the wave frequency. Based on the time domain simulation results, there was not a significant difference in power between the geometries when variation in drag was not considered, but the elliptical geometry had the highest power when using approximate drag coefficients. Using the two degree-of-freedom (2DOF) model with approximate drag coefficients, the elliptical cross section had a max power of 27.1 W and 7.36% capture width ratio (CWR) for regular waves and a max power of 8.32 W and 2.26% CWR for irregular waves. Using the three degree-of-freedom (3DOF) model with approximate drag coefficients, the elliptical cross section had a max power of 22.5 W and 6.12% CWR for regular waves and 6.18 W and 1.68% CWR for irregular waves. A mooring stiffness study was performed with the 3DOF model, showing that mooring stiffness can be increased to increase relative motion and therefore increase power. / Master of Science / As a clean, abundant, and renewable source of energy with a strategic location in close proximity to global population centers, ocean wave energy shows major promise. Although much wave energy converter development has focused on large-scale power generation, there is also increasing interest in small-scale applications for powering the blue economy. There are many situations where large-scale wave energy converter (WEC) devices are not necessary or practical, but easily-portable, small-sized WECs are suitable, including navigation signs, illumination, sensors, survival kits, electronics charging, and portable desalination. In this thesis, the objective was to optimize the performance of small-sized, oscillating body wave energy converters. Oscillating body WECs function by converting a device's wave-driven oscillating motion into useful power. Two types of oscillating body WECs were studied: bottom hinged and two-body attenuator. For the bottom-hinged device, the goal was to show the feasibility of a WEC and desalination system using numerical modeling to estimate the system performance. Based on the model results, the system will produce desirable amounts of fresh water with suitably low concentration and be effective at discharging brine. The objective for the two-body attenuator was to develop a method of power maximization through resonance tuning and numerical simulation. Based on the two- and three-degree-of-freedom model results with approximate drag coefficients, the elliptical cross section had the largest power absorption out of three different geometries of body cross sections. A mooring stiffness study with the three-degree-of-freedom model showed that mooring stiffness can be increased to increase power absorption.
| Identifer | oai:union.ndltd.org:VTETD/oai:vtechworks.lib.vt.edu:10919/103861 |
| Date | 14 June 2021 |
| Creators | Capper, Joseph David |
| Contributors | Mechanical Engineering, Zuo, Lei, Qiao, Rui, Lin, Shihong |
| Publisher | Virginia Tech |
| Source Sets | Virginia Tech Theses and Dissertation |
| Detected Language | English |
| Type | Thesis |
| Format | ETD, application/pdf |
| Rights | In Copyright, http://rightsstatements.org/vocab/InC/1.0/ |
Page generated in 0.0098 seconds