Master of Science - Science / The theoretical investigation of the Optical Kerr Effect (OKE) and Third- Harmonic Generation (THG) of Au-VO2 nanocomposite thin-films undertaken in this project is motivated by the potential use of the Au-VO2 nanocomposite in nonlinear optical (NLO) devices. NLO devices are a driving force in today fs high technology industry. In this thesis the OKE is estimated and computed and will be compared later to the measured OKE using the Z-scan interferometric laser technique [47]. This is a simple yet highly sensitive single-beam experimental
technique used to determine the real part of the dielectric susceptibility.
The study of the OKE in these composites has shown that it has a high value, comparable to that found in Au-SiO2, Au-TiO2 and Au-Al2O3 thin-films [29, 33]. This is despite the fact that the Au volumetric concentration in the Au-VO2 composites considered here is 10 percent at most, whereas in the other above mentioned composite thin-films the volumetric concentration range was between 5 − 60 percent. Moreover, it has been demonstrated that the OKE is thermally tunable in the Au-VO2 thin-films, owing to the thermally tunable optical properties of the VO2 [8, 38]. It is found that the magnitude of the OKE is of the order of 10−6 esu when the composite is below 68 0C and it is of the order of 10−7 esu when the nanocomposite thin-film is above 68 0C.
The large enhancement of the OKE is due to the surface plasmon resonance (SPR) of the nanogold particles. Its fast response, which is of the order of few picoseconds [4, 6, 7], makes the Au-VO2 nanocomposite a good candidate as a fast thermally tunable optical switch or modulator.
The modelling here of high-order harmonic generation in strongly absorbing media, as regards the amplitude of the primary beam, takes into account pump attenuation only, due to the absorption of light by the media. It is not concerned with pump depletion which is a consequence of the transfer of energy to
the harmonics and which is small by comparison with attenuation in absorbing media. The modelling is applied to the so-called transmission and reflection configurations.
The former refers to the case in which the high-order harmonic wave is monitored in the same direction as the input fundamental wave, whereas the latter describes the situation in which the fundamental wave is in the opposite direction to the high-order harmonic one.
To analyse high-order harmonic generation one has to relate the high-order harmonic intensity to the fundamental intensity [1, 9, 10, 34-36]. In so doing, a general formula for analysing high-order harmonic generation is obtained and
reduced to the particular case pertaining to THG in strongly absorbing media.
The ratio of the third-harmonic intensity to the fundamental intensity is termed the conversion coefficient or the conversion efficiency, and it is denoted by ā [23, 34]. It is useful in the sense that it expresses quantitatively the amount of input light of frequency ą converted into light of frequency ną, where
n is the order of nonlinear polarisation [1].
It is found that the THG conversion coefficient is higher the higher the laser intensity. It is thus advantageous to use a pulsed laser, which achieved very high intensities for short periods, separated by long off periods. The net harmonic output in this case is much higher than one would obtain with a continous laser of the same average output. It is found here that ƒÅ is greater in the reflection configuration compared to the transmission one above and below Tt in the photon energy range 1.0 − 3.0 eV, see Fig. 5.1 to 5.8.
However, the conversion efficiency for THG in the Au-VO2 nanocomposites for the picoseconds laser illumination we have considered, is still extremely low, and it is difficult to see a potential use for this system as a tunable frequency converter. The situation would become more favorable with the use of femtosecond
laser pulses, where for the same pulse energy the intensity is much greater.
The laser pulse energy must be limited to avoid excessive heating of the thin-film. The heat generated as a consequence of the illumination of the thin-film by the laser [23] may be controlled by using a simple cooling device which consists of a substrate on which the thin-film is deposited. The choice of such a substrate depends on whether THG is monitored in the transmission or reflection configuration. In the former a transparent substrate must be used (for example diamond) whereas in the latter an opaque substrate may be used (for example
Ag). Calculations pertaining to the removal of heat from the illuminated film are reported, and show that thermal control is manageable but only within limits.
To avoid a temperature rise of more than 5 0K the peak laser intensity we found must not exceed 7.4 ~105Wcm−2 with a pulse duration of 5 ps.
| Identifer | oai:union.ndltd.org:netd.ac.za/oai:union.ndltd.org:wits/oai:wiredspace.wits.ac.za:10539/259 |
| Date | 22 March 2006 |
| Creators | Nkulu, Mulunda Franly |
| Source Sets | South African National ETD Portal |
| Language | English |
| Detected Language | English |
| Type | Thesis |
| Format | 1625199 bytes, application/pdf, application/pdf |
Page generated in 0.0024 seconds