Next generation aerospace vehicles require thermal protection system (TPS) materials that are capable of withstanding the extreme aerothermal environment during hypersonic flight (>Mach 5 [>1700 m/s]). Ultra-high temperature ceramics (UHTC) such as zirconium diboride (ZrB₂) are candidate TPS materials due to their high-temperature thermal and mechanical properties and are often the basis for advanced composites for enhanced oxidation resistance. However, ZrB₂ matrix impurities in the form of boron trioxide (B₂O₃) and zirconium dioxide (ZrO₂) limit the high-temperature capabilities. Electric based sintering techniques, such as spark plasma sintering (SPS), that use joule heating have become the preferred densification method to process advanced ceramics due to its ability to produce high density parts with reduced densification times and limit grain growth. This study focuses on a combined experimental and thermodynamic assisted processing approach to enhance powder purity through a carbo- and borocarbo-thermal reduction of oxides using carbon (C) and boron carbide (B₄C). The amount of oxides on the powder surface are measured, the amount of additive required to remove oxides is calculated, and processing conditions (temperature, pressure, environment) are controlled to promote favorable thermodynamic reactions both during thermal processing in a tube furnace and SPS. Untreated ZrB₂ contains 0.18 wt%O after SPS. Additions of 0.75 wt%C is found to reduce powder surface oxides to 0.12 wt%O. A preliminary Zr-C-O computational thermodynamic model shows limited efficiency of carbon additions to completely remove oxygen due to the solubility of oxygen in zirconium carbide (ZrC) forming a zirconium oxycarbide (ZrCₓOᵧ). Scanning electron microscopy (SEM) and scanning transmission electron microscopy (STEM) with atomic scale elemental spectroscopy shows reduced oxygen content with amorphous Zr-B oxides and discreet ZrO₂ particle impurities in the microstructure. Processing ZrB₂ with minimal additions of B₄C (0.25 wt%) produces high purity parts after SPS with only 0.06 wt%O. STEM identifies unique “trash collector” oxides composed of manufacturer powder impurities of calcium, silver, and yttrium. A preliminary Zr-B-C-O thermodynamic model is used to show the potential reaction paths using B₄C that promotes oxide removal to produce high-purity ZrB₂ with fine grains (3.3 𝜇m) and superior mechanical properties (flexural strength of 660MPa) than the current state-of-the-art ZrB₂ ceramics. Due to the desirable properties produced using SPS, there is growing interest to advance processing techniques from lab-scale (20 mm discs) to large-scale (>100 mm). The advancement of SPS technologies has been stunted due to the limited power and load delivery of lab-scale furnaces. We use a large scale direct current sintering furnace (DCS) to address the challenges of producing industrially relevant sized parts. However, current-assisted sintering techniques, like SPS and DCS, are highly dependent on tooling resistances and the electrical conductivity of the sample, which influences the part uniformity through localized heating spots that are strongly dependent on the current flow path. We develop a coupled thermal-electrical finite element analysis model to investigate the development and effects of tooling and current density manipulation on an electrical conductor (ZrB₂) and an electrical insulator, silicon nitride (Si₃N₄), at the steady-state where material properties, temperature gradients and current/voltage input are constant. The model is built based on experimentally measured temperature gradients in the tooling for 20 mm discs and validated by producing 30 mm discs with similar temperature gradients and grain size uniformity across the part. The model aids in developing tooling to manipulate localize current density in specific regions to produce uniform 100 mm discs of ZrB₂ and Si₃N₄.
| Identifer | oai:union.ndltd.org:arizona.edu/oai:arizona.openrepository.com:10150/621315 |
| Date | January 2016 |
| Creators | Pham, David, Pham, David |
| Contributors | Corral, Erica L., Corral, Erica L., Muralidharan, Krishna, Loy, Doug, Manga, Venkateswara R. |
| Publisher | The University of Arizona. |
| Source Sets | University of Arizona |
| Language | en_US |
| Detected Language | English |
| Type | text, Electronic Dissertation |
| Rights | Copyright © is held by the author. Digital access to this material is made possible by the University Libraries, University of Arizona. Further transmission, reproduction or presentation (such as public display or performance) of protected items is prohibited except with permission of the author. |
Page generated in 0.2215 seconds