Return to search

Development of Impedimetric Immunosensor for Fumonisin on Polyanilino-Carbon Nanotubes Doped with Palladium Telluride Nanocrystals

Philosophiae Doctor - PhD / Immunosensors are affinity ligand-based biosensor solid-state devices in which the immunochemical reaction is coupled to a transducer. The specificity of the molecular recognition of antigens by antibodies to form a stable complex is the basis of the immunosensor on the electrode. The development of such a sensor requires a better design and preparation of an optimum interface between the biomolecules and the detector material. The immunosensors were developed based on Polyaniline derivative composite. Novel water soluble PdTe quantum dots (QD) was synthesized and characterized by different physical techniques such as UV-Visible (UV-VIS), Fluorescence Spectroscopy (PL), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD). The electroactivity of such synthesized quantum dots was studied by cyclic voltammetry in aqueous media. The synthesis of poly(2,5-
dimethoxyaniline)-multi wall 'carbon nanotubes nanocomposite was carried out by electropolymerization in situ of 2,5-dimethoxyaniline - multi wall carbon nanotubes (PDMA-MWCNT) from aqueous dispersion containing acid-treated multi wall carbon nanotubes (MWCNT) and 2,5-dimethoxyaniline subsequently modifying a glassy carbon electrode in acid media. An undoped PDMA was also prepared for control. The composite for this work, consists of layer-by-layer method to form a multilayer film of QDs and PDMA-MWCNT. The method used was as follows; the drop coating of quantum dots followed by electrodeposition of poly(2,5- dimethoxyaniline )-carbon nanotubes onto surface of glassy carbon. The PDMA-CNT was characterized by UV-Visible (UV-Vis), Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The electrochemical characterisation of PDMA-CNT was carried out using cyclic voltammetry (CV) and Electrochemical Impedance Spectroscopy (EIS). The composite (QDs-PDMA-MWCNT) was also characterized using above mentioned techniques. The electrochemical immunosensor for fumonisin a mycotoxin was prepared by dropcoating of mycotoxins antibody onto the composite modified glassy carbon electrode. The response profiles of fumonisins sensors system were obtained from electrochemical
impedance spectroscopy (EIS) measurements. The fumonisin immunosensor was used for the detection of fumonisins in certified com reference materials. For comparison reasons, analysis of such mycotoxins was carried out by using conventional analytical method enzyme-linked immunosorbent assay (ELISA). The EIS response of FBI immunosensor (GCEIPT-PDMA-MWCNT/anti-Fms-BSA) gave a linear range of 7 to 49 ng L-I and the corresponding sensitivity and detection limits were 0.0162 ka L ng-I and 0.46 pg L-I, respectively. Hence the limit of detection of GCEIPT-PDMA-MWCNT immunosensor for fumonisins in com certified material was calculated to 0.014 and 0.011 ppm for FBI, and FB2 and FB3, respectively. These results are lower than those obtained by ELISA, a provisional maximum tolerable daily intake (PMTDI) for fumonisins (the sum of FBI, FB2, and FB3) established by the Joint FAO / WHO expert committee on food additives and contaminants of 2 ug kg" and the maximum level recommended by the U.S. Food and Drug Administration (FDA) for protection of human consumption (2-4 mg L-I).

Identiferoai:union.ndltd.org:netd.ac.za/oai:union.ndltd.org:uwc/oai:etd.uwc.ac.za:11394/8792
Date January 2013
CreatorsMasikini, Milua
Contributorslwuoha, Emmanuel
PublisherUniversity of the Western Cape
Source SetsSouth African National ETD Portal
LanguageEnglish
Detected LanguageEnglish
RightsUniversity of the Western Cape

Page generated in 0.0028 seconds