Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 25 for “"3D packaging"”.
-
The Development of Novel Interconnection Technologies for 3D Packaging of Wire Bondless Silicon Carbide Power Modules
This dissertation advances the cause for the 3D packaging and integration of silicon carbide power modules. 3D wire bondless approaches adopted for enhancing the performance of silicon power modules were surveyed, and their merits were assessed to serve as a vision for the future of SiC power …
-
Applications of Additive Manufacturing Technologies to Ambient Energy Harvesters for Microwave and Millimeter-Wave Autonomous Wireless Sensing Networks and 3D Packaging Integration
… not only energy harvesters but also mm-wave IC packaging process. Ambient energy harvesting techniques collect ambient energy such as solar, RF, heat, and vibration and convert them into DC power sources to support the energy requirement of electronics. Since the energy is provided autonomously …
-
Interconnect Design and System Integration For 3D RF Reconfigurable Structures in Communications Applications
3D packaging is broadening horizons for radio frequency (RF) electronic systems. In wireless sensor networks, 3D packaging can be used to reduce the form factor of wireless sensor nodes. Additive manufacturing is the desired means of fabrication for these wireless sensor nodes due to its low cost …
-
A Deep Reinforcement Learning Approach to Packaging Optimization
Packaging optimization is the process of determining an optimal layout of components in an assembly with the goal of maximizing packing density. Existing computational tools for solving packaging optimization problems are focused in their scope, as they are often tailored to specific problems, and …
-
Electrical modeling, design and characterization of tapered through-package-vias in glass interposers for high-performance applications
Three dimensional (3D) packaging technologies are being developed to address the escalating demand for data traffic at lowest power consumption, smallest form factors, and lowest cost. Glass has been proposed as a compelling alternative to silicon and the best packaging substrate for interposer, …
-
3D Heterogeneous Integration for RF/mmWave Electronics
RF/mmWave systems require 3D packaging solutions that maintain signal integrity while enabling heterogeneous integration, yet conventional implementations remain constrained by lossy off-chip interconnects and package-bound architectures. This thesis investigates whether interconnects can be …
-
Design Algorithms and Methodologies for Heterogeneous 2.5D and 3D Integrated Circuits
… both power and performance in emerging 2.5D and 3D ICs. Due to transistor scaling challenges and power limitations in complex Gigabit Systems on Chip (SoC), chiplet integration is a promising approach to address these issues with the following benefits. First, the chiplet reduces the design …
-
Design and self-calibration scheme for RF circuits using mems in 3D packages
… switches (MEMS) using three dimensional (3D) through-silicon via (TSV) packaging technology. The LNA can self-calibrate its gain and noise figure (NF). On-chip testing is performed using a peak detector and a digital signal processor (DSP). A low-cost self-calibration scheme is proposed …
-
Benchmark Framework for 2-D/3-D Integrated Compute-in-Memory Based Machine Learning Accelerator
… and back-propagation. The work is extended to 3D integration, as 3D+NeuroSim framework to support electrical-thermal co-simulation of 3D integrated CIM accelerators, for both of monolithic and heterogeneous 3D integration. The proposed NeuroSim family is publicly available at …
-
Effect of Organic Precursor and Annealing on Porosity and Dielectric Properties of Alucone Films for Low-k Materials
… in transistordensity and the development of 3D packaging have accelerated computational processing, memory, and transmission speeds. Low-k dielectric material is an essential component in advanced semiconductors to isolate interconnect wires, prevent current leakage, and minimize RC delays. …
-
Design and Demonstration of 3D Glass Panel Embedded (GPE) Package for Superior Bandwidth and Power-Efficiency
… for package-level integration are either 2D/3D and chip-first/chip-last, based on how the chips are assembled. While some 3D and chip-first technologies solve the interconnect length and I/O count challenges, they are still fundamentally limited in scaling the bandwidth and power-efficiency …
-
Electrical modeling , design and high-frequency characterisation of through-package-vias in ultra-thin 3d glass interposers
System scaling by 3D packaging is now considered a critical technology enabler for continued increases in system data bandwidth, at lowest power and cost. Ultra-high chip-to-chip interconnect bandwidth is required for variety of new applications including 5G communications, V2V (vehicle-to-vehicle) …
-
Computational Studies of Thermal Properties and Desalination Performance of Low-dimensional Materials
… and integrated on a single microchip through 3D packaging and chip stacking technology. A large amount of heat will be generated in a limited space during the operation of microchips. Moreover, there is a high possibility of hot spots due to non-uniform integrated circuit design patterns as …
-
Investigation of processing condition on the reliability and performance of future memory devices
… employed due to the placement accuracy for 3D packaging technology and manufacturing 3D high bandwidth memory (HBM) DRAM modules. In addition to utilizing TCB technology to DRAM modules, memristors as an emerging memory is another memory class that can help overcome the scaling limit and …
-
Advanced Structures and Compositions for 3D Forming of Cellulosic Fibers
… and green treatments were applied to develop 3D packaging structures. Formability, the material's ability for three-dimensional shaping, was achieved by plastic deformations in paper structures that were defect-free in terms of appearance and functionality. A set of methods to improve paper …
-
Chip-Package Nano-Structured Copper and Nickel Interconnections with Metallic and Polymeric Bonding Interfaces
… mixed signal systems are driving the need for 3D packaging with embedded active components and ultra-short interconnections. Being able to provide several fold increase in the chip-to-package vertical interconnect density is essential for garnering the true benefits of nanotechnology that will …
-
Numerical modelling of electrodeposition process for printed circuit boards manufacturing
… particularly for high technology products (e.g., 3D packaging), is to manufacture PCBs with high aspect ratio (AR) vias. Typically, the size of such a via is at the micrometer scale (this is why they are termed micro-vias). The most widely used technique for manufacturing micro-vias is …
-
Integrated Thermal Management Strategies for Embedded Power Electronic Modules
… and offer the advantage of three-dimensional (3D) packaging of electronic components in a small and compact volume, replacing the traditional wire bonding technology. They have the potential to offer reduced time and effort associated with developing and manufacturing power processors. However, …
-
Acoustic Micro Imaging based Reliability Testing and Life Prediction of Electronic Packages
… life of electronics systems. As microelectronic packaging technology moves to three-dimensional (3D) packaging with higher integration of functional components, the ever-increasing power density of the chip and the complex multi-layer structures have made the thermal management and heat …
-
Non-destructive evaluation of solder joint reliability
… A comprehensive review of current and emerging packaging and interconnect technologies has shown increasingly a move from conventional 2D to 3D packaging. These present new challenges for reliability and Non Destructive Evaluation (NDE) due to solder joints being hidden beneath the packaging, …
Page 1 of 2