Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 11 of 11 for “"Anodic Etching"”.

  1. Study of the pit initiation mechanism and metal dissolution kinetics during anodic etching of aluminum

    … processes during the initial stages of etching were thoroughly characterized to evaluate the hypothesis that voids are the primary pit initiation sites. Dissolution rate measurements made in etch pits revealed contradicting trends of constant and potential dependent dissolution current …

    iastate Repository record for Study of the pit initiation mechanism and metal dissolution kinetics during anodic etching of aluminum (opens in a new tab)

  2. Silicon needle-like surfaces for room temperature si-si bonding applications

    … Silicon (Si) surfaces are functionalized using anodic etching of silicon wafers in a hydrofluoric acid (HF) based electrolyte to create self-organized needle-like surfaces. Such self-organized needlelike surfaces allow repeated bonding and debonding of the same surfaces with<br>adequate bond …

    freiburg-diss Repository record for Silicon needle-like surfaces for room temperature si-si bonding applications (opens in a new tab)

  3. Measurement and modeling of oxide passivation kinetics in aluminum etch tunnels

    … is induced by negative ramp changes in anodic etching current. Scanning electron microscopy is used to measure the area passivated. Potential transients are analyzed to identify a possible driving force for passivation. The transients are characterized by two regions: first an initial …

    iastate Repository record for Measurement and modeling of oxide passivation kinetics in aluminum etch tunnels (opens in a new tab)

  4. Studies on the Control of Metal Passivation in the Electrochemical Tunnel Etching of Aluminum (Corrosion, Passivity, Pitting Potential, Aluminum)

    … of the corrosion tunnels formed on aluminum by anodic etching in hot aqueous chloride solutions was studied. In the hypothesized mechanism, electrolyte diffusion in the tunnels maintained the tips of all tunnels at the equilibrium potential of an electrochemical reaction involving adsorption of …

    uiuc Repository record for Studies on the Control of Metal Passivation in the Electrochemical Tunnel Etching of Aluminum (Corrosion, Passivity, Pitting Potential, Aluminum) (opens in a new tab)

  5. The photolithographic patterning of porous silicon using silicon nitride and silicon carbide films as masks

    … projected on the sample by illumination during anodic etching in HF:ethanol solution which produced microcracks in regions illuminated during anodization. Creation of these microcracks resulted in formation of porous silicon in the underlying regions. The cracking is related to the stress in the …

    njit Repository record for The photolithographic patterning of porous silicon using silicon nitride and silicon carbide films as masks (opens in a new tab)

  6. Removal of dislocation cores from multicrystalline silicon by etching

    … to be studied and optimised.</p><p>The first etching system explored is the Secco etch (1 K₂Cr₂O₇ (0.15M):2 HF (49%)), a commonly used defect-revealing etch. Samples are immersed in Secco etch for various durations at a range of temperatures, and pits are formed at the locations of …

    oxford Repository record for Removal of dislocation cores from multicrystalline silicon by etching (opens in a new tab)

  7. The anodic behaviour of U, Ti, Zr, Nb and Ta in non-aqueous ethereal solutions

    … were readily obtained on steel specimens, after anodic etching in acid solution. Deposits obtained on U specimens, even after etching in acid to remove the oxide film, had poor adhesion and only moderate covering power. Anodic polarization of U specimens in the organic plating solution prior to …

    london-metro

  8. The roles of the surface oxide film and metal-oxide interfacial defects in corrosion initiation on aluminum

    … and potential transients were measured during anodic oxidation of aluminum. The ratio of the experimental faradaic current density to the predicted one using high field model, p, was calculated. The measured faradaic current is about 104 times smaller than that predicted by this model …

    iastate Repository record for The roles of the surface oxide film and metal-oxide interfacial defects in corrosion initiation on aluminum (opens in a new tab)

  9. A Study of Novel Fabrication Techniques for Development of 3-D Silicon Nano-structure Array

    … of silicon surface in TMAH using anisotropic etching technique, 2) formation of porous layer on patterned silicon surface using electrochemical anodic etching, and 3) treatment of porous silicon layer using an alkaline etching to reveal the silicon nano-structure array. The second fabrication …

    concordia Download PDF for A Study of Novel Fabrication Techniques for Development of 3-D Silicon Nano-structure Array (opens in a new tab)

  10. Porous silicon microparticles as an embolic agent for the treatment of hepatocellular carcinoma

    … properties based on photolithography and anodic etching. These microparticles function as multistage drug delivery systems that can circumvent the biobarriers present in the systemic circulation enabling site-specific localization and release of chemotherapy and imaging agents. The …

    texas Repository record for Porous silicon microparticles as an embolic agent for the treatment of hepatocellular carcinoma (opens in a new tab)

  11. Fabrication and Characterization of a Palladium/Porous Silicon Layer

    … component of an electrochemical gas sensor. Etching pores into silicon is an electrochemical process; and which type of doped silicon used is one of its key parameters. For nearly all reported porous silicon gas sensors, the silicon has been of the p-doped variety – because p-doped porous …

    calpoly Repository record for Fabrication and Characterization of a Palladium/Porous Silicon Layer (opens in a new tab)