Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 11 of 11 for “"Autoclave Manufacturing"”.

  1. Out of autoclave manufacturing of CFRPs having multiscale reinforcement for improved interlaminar fracture toughness and multifunctional characteristics

    … thedirect introduction of CNTs during Out-of-Autoclave (OoA) processes such as liquid resin infusion (LRI) or resin transfer molding (RTM).The present Dissertation aims to the development of Out-of-Autoclave Carbon Fibre Reinforced Polymers (CFRPs) with improved interlaminar fracture toughness …

    greece Repository record for Out of autoclave manufacturing of CFRPs having multiscale reinforcement for improved interlaminar fracture toughness and multifunctional characteristics (opens in a new tab)

  2. Void characterisation of composite prepreg laminates using X-ray Imaging and Deep Learning methods

    Out-of-Autoclave manufacturing is an emerging lower-cost alternative to produce composite components, however, higher porosity (>2%) is often observed due to the 3–7x reduction of the consolidation pressure compared to autoclave manufacturing. For this reason, fully characterising the composite …

    bristol Repository record for Void characterisation of composite prepreg laminates using X-ray Imaging and Deep Learning methods (opens in a new tab) Download PDF for Void characterisation of composite prepreg laminates using X-ray Imaging and Deep Learning methods (opens in a new tab)

  3. Improving Integrally Heated Composite Tooling Through Cold Sprayed Copper Coatings and Heat Transfer Simulations

    … (IHCT) is seen as a low cost alternative to autoclave manufacturing of polymer matrix composites (PMCs). IHCTs consist of a composite tool heated by surface heaters; temperature distribution is ensured by a thermally conductive metallic layer. The main original contributions of this thesis …

    ottawa-retro Repository record for Improving Integrally Heated Composite Tooling Through Cold Sprayed Copper Coatings and Heat Transfer Simulations (opens in a new tab)

  4. Elastically Coupled Numerical Fluid Models for Flows Found in Composites Manufacturing

    Void formation is a common issue in the manufacturing of carbon fibre composites. In particular, composites produced using out-of-autoclave manufacturing, which offers an emerging low-cost alternative to autoclave manufacturing, can experience high porosity (greater than 2\%) due to decreased …

    bristol Repository record for Elastically Coupled Numerical Fluid Models for Flows Found in Composites Manufacturing (opens in a new tab) Download PDF for Elastically Coupled Numerical Fluid Models for Flows Found in Composites Manufacturing (opens in a new tab)

  5. High temperature polymer composites using out-of-autoclave processing

    … usually manufactured, under high pressure, in an autoclave which requires high capital investments and operating costs. In contrast, out-of-autoclave manufacturing, specifically vacuum-bag-only prepreg process, is capable of producing low cost and high performance composites. In the current study, …

    must-thes Repository record for High temperature polymer composites using out-of-autoclave processing (opens in a new tab)

  6. Compressibility Measurement and Modeling to Optimize Flow Simulation of Vacuum Infusion Processing for Composite Materials

    Out-of-autoclave manufacturing processes for composite materials are increasing in importance for aerospace and automotive industries. Vacuum Infusion processes are leading the push to move out of the autoclave. An understanding of the various process parameters associated with resin infusion is …

    byu Repository record for Compressibility Measurement and Modeling to Optimize Flow Simulation of Vacuum Infusion Processing for Composite Materials (opens in a new tab) Download PDF for Compressibility Measurement and Modeling to Optimize Flow Simulation of Vacuum Infusion Processing for Composite Materials (opens in a new tab)

  7. Predicting and measuring thermal conductivity in carbonepoxy unidirectional tape and textile reinforced composites

    … parts and moulds has a strong effect on out-of autoclave manufacturing operations. Limited thermal conductivity and variability data is available for composites made from carbon fibres that are widely used in mould and aircraft construction. A summary of experimental measurements and directional …

    ottawa-retro Repository record for Predicting and measuring thermal conductivity in carbonepoxy unidirectional tape and textile reinforced composites (opens in a new tab)

  8. Permeability Characterization and Fluorescent Void Flow Monitoring for Processing Simulation

    … in importance alternative to traditional prepreg-autoclave methods for manufacture aerospace composites. The most significant roadblock to industry's implementation of LCM is the optimization of resin flow to ensure high quality parts. This study developed process optimization tools to foster the …

    byu Repository record for Permeability Characterization and Fluorescent Void Flow Monitoring for Processing Simulation (opens in a new tab) Download PDF for Permeability Characterization and Fluorescent Void Flow Monitoring for Processing Simulation (opens in a new tab)

  9. Thermal Cycle Effects on Laminated Composite Plates Containing Voids

    … brackets / fittings) are often cured in an autoclave to acquire the required space grade quality. These days the industry is focusing on out of autoclave manufacturing methods which leads to more voids inside the laminate compared to those manufactured in the autoclave. In this work, the …

    concordia Download PDF for Thermal Cycle Effects on Laminated Composite Plates Containing Voids (opens in a new tab)

  10. In-situ Characterization and Machine Learning Applications for Composite Processing

    … operational efficiency and overall performance. Autoclave composite processing offers a solution for the intricate design of complex structures. However, the rapid temperature and strain fluctuations experienced during the processing gives rise to a multitude of defects and residual stresses in …

    embry-riddle Repository record for In-situ Characterization and Machine Learning Applications for Composite Processing (opens in a new tab)