Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 31 for “"Autoclave Processing"”.
-
High temperature polymer composites using out-of-autoclave processing
… usually manufactured, under high pressure, in an autoclave which requires high capital investments and operating costs. In contrast, out-of-autoclave manufacturing, specifically vacuum-bag-only prepreg process, is capable of producing low cost and high performance composites. In the current study, …
-
Out-of-autoclave processing development of aerospace carbon fibre polymer composites
… a wide range of manufacturing parameters for RTMprocessing. This was carried out by developing a thermal and cure simulation tool usingMATLAB_Simulink and connecting the model to the response surface method (RSM).Initially, cure kinetics of epoxy resin were studied through thermal analysis. As a …
-
Efficient methods for non-linear thermochemical analysis of composite structures undergoing autoclave processing
… modelling of complex composite structures during processing.
-
Additive manufacture of dissolvable tooling for autoclave processing of fiber reinforced polymer composites
Autoclave processing of advanced fiber reinforced polymer composites (AFRPC) uses applied heat and pressure to yield high quality composite components. Geometrically accurate and thermally stable molds or tools are used to maintain the part form until the part cures and rigidizes. For high-volume …
-
An integrated model of the development of process-induced deformation in autoclave processing of composite structures
… major identified deformation sources. A 'virtual autoclave' concept is employed in which autoclave control algorithms and autoclave response are simulated to predict structure boundary conditions during processing. Characterization of a carbon fibre/epoxy composite is performed and models …
-
Experimental and Numerical Studies on the Effects of Environmental Conditions on Defect Formation during Autoclave Processing of Prepreg
… laminate quality. This is commonly achieved by autoclave prepreg processing where, in addition to the vacuum pressure, high external pressures during the resin cure stage enhance consolidation. As a result, parts of simple geometry can be manufactured with relative ease having fibre volume …
-
Characterization and simulation of process-induced wrinkling in manufacture of aerospace textile composites
… aims to expand the existing knowledge on autoclave processing of woven composite prepregs, especially in the uncured state, through a combined experimental and numerical approach including enhanced modelling of the mechanics involved during the forming and consolidation stages. An emphasis …
-
Efficient numerical techniques for predicting process-induced stresses and deformations in composite structures
… of research work in numerical modelling of autoclave processing of composite structures, several models have been developed ranging from simple one-dimensional elastic to sophisticated three dimensional viscoelastic models. Some of the common problems faced by these numerical models are the …
-
Additively Manufactured Continuous Carbon Fiber Thermoplastic Composites for High-Performance Applications
… of manufacturing complex geometries, out-of-autoclave processing, elimination of the need for composite tooling, and the ability to perform lights-out manufacturing. Currently, however, a suite of challenges related to modelling, design, manufacturing defects, and general limitations in the …
-
Outgassing Of Out-Of-Autoclave Composite Primary Structures For Small Satellites
Out-of-autoclave vacuum-bagged-only (VBO) processing is capable of producing lower cost composite primary structures for small satellites than autoclave processing. However, the outgassing performance of VBO structures in a vacuum environment has not been examined. Panels were manufactured from …
-
Development and characterisation of a fibre-optic acoustic emission sensor
… composite laminate that was fabricated using autoclave processing. The embedded fibre-optic sensor was found to provide higher sensitivity to simulated AE compared with a surface-mounted sensor. Sensor characterisation trials were performed using simulated AE; a low directional sensitivity was …
-
Characterization and modeling of shear stress during manufacturing and thermal properties of structural composite materials
… temperatures and pressures similar to those of autoclave processing. This methodology includes the development of a testing rig that mimics the deformation mismatch between tools and parts, and quantifies shear stress—that is, tool-part friction or shear stress of sandwich structures. Discrete …
-
Characterization of Bistability Behavior in Unsymmetric CFRP Laminates
… different aspect ratios were fabricated using autoclave processing. Digital image correlation (DIC) is used to monitor laminate strains in situ during the processing of the composite and to correlate processing strains to the degree of bistable behavior in differently sized samples. …
-
Gas transport and void evolution in composite prepregs
Out-of-autoclave (OOA) processing of prepregs represents a promising low cost alternative to expensive autoclave processing, which today is the standard method for producing high-quality CFRP parts such as aerospace structures; however, OOA processes have a greater potential to experience problems …
-
Core movement during processing of sandwich panels
… that plagues sandwich panel fabrication during autoclave processing. External pressure can result in deformation of the core in its weak, lateral direction. This in turn, drags the facesheet plies inward. Parts displaying notable core movement are unfit for service and must be scrapped. …
-
Gas transport in out-of-autoclave prepreg laminates
Out-of-autoclave (OOA) pre-impregnated (prepreg) materials are a prospective alternative to traditional autoclave processing, with the potential to reduce processing costs and build structures without size limitations imposed by the autoclave. Gas transport pathways in prepreg laminates play an …
Page 1 of 2