Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 227 for “"Axial loads"”.
-
Behavior of a Single Micropile in Sand Under Cyclic Axial Loads
Mechanisms causing cyclic degradation of skin friction and accumulated permanent displacement are found from investigation of changes in effective stresses and volumetric strains during cyclic loading.
-
Behaviour of bolted end-plate connections for glulam braces under cyclic axial loads
… in glulam braces are studied under cyclic axial loads to gain an in-depth understanding of the structural properties and failure mechanisms. A total of forty-five specimens were tested consisting of fifteen sets with five varying parameters, including the number of bolts, diameter of the …
-
Behaviour of Partially Composite Precast Concrete Sandwich Panels under Flexural and Axial Loads
… reducing shear deformations. Ultimate loads increased from 58 to 80% that of a composite section as the connectors’ reinforcement ratio increased from 2.6 to 9.8%. This design was optimized by reinforcing the studs and integrating them with the structural wythe; new connectors composed …
-
Structural Performance of Sandwich Concrete Walls including UHPC and GFRP Reinforcement under Bending and Axial Loads
… under out-of-plane bending (M) with and without axial loading (N) applied to one wythe to simulate both architectural and load-bearing walls. The study compared steel and PVA fibers in the UHPC, and examined GFRP reinforcement ratio in the wythes, insulation thickness, amount and configurations …
-
Parametric Finite Element Analysis of Large Diameter Shell Intersections Subjected to Internal Pressure and Axial Loads
… are subjected to internal pressure and an axial load on the intersecting cylinder. The internal pressure and axial load cases are considered independently and simultaneously, where the d/D ratio of the intersecting cylinders ranges from 0.333 to 1.0. By using this range of diameter ratios, …
-
Prediction of the running torque of instrument ball bearings at high speed under combined radial and axial loads
… rpm with various combinations of radial and axial load ranging between 0 and 200 grams. Because of the lack of experimental data for instrument bearings over any range of speeds, loads and sizes, it was necessary to construct a suitable bearing tester and accumulate the required data. The …
-
The measurement of the running torque of oil and grease lubricated instrument ball bearings under combined radial and axial loads
… up to 40,000 rpm while under combined radial and axial load. Much of this investigation was devoted to the construction of an accurate torque sensing device. The method employed relied on the amplification of strain gage signals by a strain gage indicator and an x-y plotter. The strain gages were …
-
Experimental and numerical investigations of Frameless cold form steel corrugated wall panels subjected to in-plane monotonic and cyclic loads
… seismic performance of Frameless panels under axial and shear loads. Within this context, a series of experimental and numerical studies are being conducted at the University of British Columbia to assess the seismic performance of Frameless panels. First, a robust experimental test setup is …
-
Effect of Column Axial Load on Skewed SMF RBS Connection Demands
… however, it is unclear how realistic column axial loads will affect the skewed connection performance. This study investigates the effects of column axial loads on skewed special moment frame connections containing reduced beam sections (RBSs). Detailed finite element analyses are used for …
-
Development of a pneumatic sensor for measuring the torque of instrument ball bearings
… of the effect on torque when both radial and axial loads were varied. In seeking to obtain improvements in methods of measuring small torques, a pneumatic sensor was developed for testing R-3 instrument ball bearings under varying radial and axial loads. This sensor was based upon the …
-
Testing and Modelling of a Reinforced Concrete Shear Wall Subjected to Combined Lateral and Axial Loading
Higher axial loading requires higher lateral loads to displace the shear walls, however, during seismic events higher axial loads reduce the shear walls’ abilities to dissipate energy. During these seismic events, the hysteretic response of shear walls with axial loading exhibits a pinching effect. …
-
Characterizing the Shear Behavior of Ultra-High-Performance Concrete through the Universal Panel Tester
… Concrete (UHPC), especially under the effects of axial loads and varying scales, poses challenges to the formulation of reliable design models. Although UHPC is being utilized in structural applications, its complex behavior under combined stress states and the influence of fiber alignment are yet …
-
Experimental Study of Unbonded Fiber Reinforced Elastomeric Bearings
… were subjected to cyclic excitation under design axial load at 0° (parallel) and 45° (diagonal) orientations. Square SU-FREI bearings achieved acceptable base isolation characteristics at both orientations despite subtle differences in their mechanical properties. Stable rollover (SR) deformation …
-
Evaluating and Relaxing the Limits on Flexural Reinforcement Ratio of Masonry Shear Walls
… limits on reinforcement ratios ("ρ" _"max" ) and axial compressive stresses (≤10% of masonry compressive strength, f_m^'), undermining masonry’s inherent compression capacity under high axial loads. This dissertation investigates the seismic performance of reinforced masonry shear walls (RMSWs) …
-
Load and Deformation Response of Tieback Walls
Axial loads in the soldier piles develop due to tieback prestressing and downdrag. The significance of the contribution from downdrag depends upon the available axial capacity of the piles and stiffness of the ground. Downdrag can be relieved during subsequent excavation by relative downward …
-
Plastic hinge length in high-rise concrete shear walls
… hinge lengths than shorter walls. Compressive axial loads reduce the plastic hinge length, tensile axial loads have the opposite effect. A simple shear model was proposed to estimate the increase in plastic hinge length when the shear stresses are high. Walls of different lengths interconnected …
-
Strength evaluation of strut-purlins
… the design problem of combined uplift and axial loads on these members is not adequately addressed in the 1989 AISI specification. The objective of this thesis is to provide experimental evidence that strut-purlins can be designed with an existing interaction equation. It was a/so the …
Page 1 of 12