Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 58 for “"Bearing surfaces"”.
-
Biotribocorrosion of Hard-on-Hard Bearing Surfaces in Orthopaedic Hip Replacements
… the corrosion currents released from the bearings during sliding. Under 0.8 mm of Microseparation the corrosion currents were found to increase by a near order of magnitude compared to Standard Gait; which resulted in an increase of estimated corrosive volume loss from approximately 0.03 - …
-
Development and Implementation of Mathematical Modeling, Vibration and Acoustic Emission Technique to Correlate <em>In Vivo</em> Kinematics, Kinetics and Sound in Total Hip Arthroplasty with Different Bearing Surfaces
… walking performance in THA subjects of various bearings surfaces was performed.</p> <p><em>In vivo</em> kinematics, kinetics, corresponding vibration and sound measurements of THA were analyzed post-operatively using video-fluoroscopy, mathematical modeling, sound sensors and accelerometers …
-
ΟΙΚΟΔΟΜΙΚΗ ΤΩΝ ΑΡΧΑΙΩΝ ΚΙΟΝΩΝ
… THE PERFECTION OF THE JOINTS; CREEPING, RESTING SURFACES, BEARING SURFACES, HORIZONTAL JOINTS; THE CONCEPT OF THE ROTATIONAL GRINDING OFF, EMPOLIA AS PIVOTS. 2. SURFACE PLATES [MARBLE SLABS WITH DIAMENSIONS CORRESPONDING TO THE SIZE OF COLUMN DRUMS, WALL BLOCKS ETC. THEY WERE USED TO REPEATEDLY …
-
Conceptual Design for a Surface-Guided Total Knee Replacement With Normal Kinematics
… of this design the shape of the articular surfaces resembled a ball-and-socket joint, and on the lateral side a pair of guiding bearing surfaces mimicked the guiding roles of the cruciate ligaments. The novelty in the design concept lies in the design of the shape of the lateral articular …
-
Metallurgical Characterisation Comparing Recycled and Ore-based Steels for Automotive Crankshafts
… A critical feature of crankshafts is their bearing surfaces which have to meet tight requirements regarding hardness and compressive residual stresses in order for the component to function properly. The properties of the bearing surfaces are to a large extent determined by a grinding …
-
Characterization of Potential Wear Sources in Knee Arthroplasty Prostheses After In Vivo Function
… from four main locations: articulating surfaces, modular component surfaces, surfaces of fixation, and adjuvant fixation devices. Each of these possible wear sources can initiate the cascade of failure associated with wear-induced osteolysis and lead to subsequent revision surgery. The …
-
Simulation and anylysis of the wear of metal on metal articulations in artificial hip joints
… components, and in particular from polyethylene bearing surfaces. Through the late 1980's and the 1990's the concept of metal on metal bearings has re-emerged as one potential solution to the clinical problems associated with polyethylene particle induced osteolysis. In this thesis both …
-
Surface Patterning, Electronic Device Fabrication And, Three-Dimensional Self-Assembly Using Polydimethylsiloxane
… the photopatterning of UVO modifications of PDMS surfaces. This modification enables the direct photoinitiated patterning of discrete PDMS patterns without the use of a master. The UVO activated PDMS regions are chemically bonded to oxide bearing surfaces with a greater strength than the modulus …
-
LASER-INDUCED ETCHING OF POLYCRYSTALLINE CERAMIC MATERIAL A12O3TiC
… of laser-induced etching on formation of air bearing surfaces in the sliders of thin film magnetic recording heads, various patterns were created on the substrate surface. A character library has also been established to facilitate the pattern formation. This is a subroutine library designed …
-
The role of cancellous bone architecture in misalignment and side effect errors
… found at the ends of long bones and similar load-bearing surfaces. Its complex architecture allows high stiffness and strength, while also minimizing the mass and metabolic needs of the bone. This architecture confounds attempts to measure cancellous bone’s mechanical properties to produce a model …
-
Determination of Indium using the dead stop end point
… use was more when it was discovered that coating bearing surfaces with the metal gave high corrosion resistance and caused the surface to retain a core complete all film (Latiner and Hildebrand, p. 1).For recently, indium has been used widely in a great many different applications. Sims (1556) and …
-
An experimental investigation of wear behavior of ultra-high molecular weight polyethylene under sliding motion
… sliding motion on the materials that are used as bearing surfaces of human total-joint replacement prostheses. The tests are performed with a specially designed equipment based on pin-on-disk machine. The testing machine is designed and constructed to reproduce sliding motion, applied to spherical …
-
Evaluation of poly-ether-ether-ketone (PEEK) for cervical disc replacement devices
… Recently, it has been proposed as a promising bearing material for cervical total disc replacement (TDR). A new bearing combination of PEEK-on-PEEK based self-mating articulation has been used, which may overcome current bearing materials related complications. For ball-on-socket based cervical …
-
Tribology of ball-and-socket total disc arthroplasty
… ball-and-socket combination. Contact between the bearing surfaces of such designs can result in high frictional torque, which can then result in wear and implant loosening. This study was designed to determine the effects of change in design factors, such as dimensions and material combinations, …
-
Lubrication and Wear Analysis of a Novel Squeeze Film Artificial Hip Joint
… cup geometry to enact separation of the bearing surfaces and improve lubrication behavior. Lateral and in-line design configurations were developed and analyzed using established finite element lubrication models with realistic gait cycle and bearing design specifications likely to be …
-
Tribocorrosion of total hip replacements
… Testing was focused around 36mm metal-on-metal bearing surfaces in both saline and bovine serum solutions but consideration was also given to metal-on-polymer interfaces. Corrosion was found to contribute substantially to material degradation within metal-on-metal contacts, both in the …
Page 1 of 3