Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 12 of 12 for “"Boring bar"”.
-
Dynamic Modeling and Dynamic Analysis of the Boring Machining System
The boring operation is a metal cutting process widely used in industry. The inherent properties of the long, slender boring bar make it susceptible to self-excited chatter during machining. The main focus of this thesis is directed at developing a system model which correctly describes the boring …
-
Parametric design of boring bars with adaptive tuned mass dampers
Slender single point boring tools are highly sensitive to chatter vibrations and require additional chatter suppression design features to avoid unstable vibrations. Tuned mass dampers (TMDs) in boring tools are vibration absorbers where the natural frequency and damping ratio of the TMD is tuned …
-
A theoretical and experimental investigation of the BTA deep hole tool support in the machining zone
… alignment with the piloting hole depends on the boring bar to which the tool appears as a solid extension. This study shows that the alterations in the output quality and the support pads' wear pattern can be explained by in-process encountered boring bar bending. This is because even minor …
-
Control of whirling vibrations in BTA deep hole boring process using fuzzy logic modeling and active suppression technique
… dimensioning and tolerances. Deep hole boring is the most complex and expensive drilling operation in terms of expertise needed, operating conditions and size. The present research is to study the whirling vibrations of the boring bar workpiece system in the BTA deep hole boring process. …
-
Active damping of machine tools with magnetic actuators
… are often found in machining operations, such as boring large cylinders, or turning long and slender shafts. The excessive flexibility of such tool or shaft may cause static deflection, forced vibration, and even chatter vibrations, which result in poor surface finish, tool breakage, and even …
-
Chatter Suppression in Boring Operations through Altering Tool Dynamics
… factors for productivity. Particularly in boring process, the long cantilevered structure of boring bar makes it the most flexible part of machine tool system. As a result, there is a high possibility for chatter to occur compared with other machine tool components. In this research, two …
-
Overhung-boring bars: The performance of undamped and damped bars under static and dynamic conditions when machining metals
… behaviour of some new designs of slug damped boring bars with a 10 to 1 overhang ratio. The bars were mounted on a centre lathe. The static behaviour of a boring bar in relation to the geometric form errors that might be produced during boring was studied both analytically and experimentally. …
-
Modeling of mechanics and dynamics of boring
… investigates the mechanics and dynamics of boring operations. The mechanics of boring operations deal with the prediction of cutting forces as a function of tool geometry, work material properties, and cutting conditions such as feed rate, radial depth of cut, and cutting speed. The dynamics …
-
Vibration Control for Chatter Suppression with Application to Boring Bars
… hardware and control system design for a boring bar application. Initially, we treat the cutting forces merely as an unknown disturbance to the structure which is essentially a cantilevered beam. We then approximate the structure as a linear single-degree-of-freedom damped oscillator in …
-
Dynamic modeling of single and multi point turning operations
… single point cutting operations like turning and boring operations. Single point cutting operations such as turning and boring, are widely used in the industry. Turning operation is used to create axisymmetric surfaces whereas the boring is a machining operation used to enlarge the inner diameters …
-
Obrábění děr pro uložení ložisek v odlitcích převodových skříní.
V této práci bude rozebrána problematika obrábění děr pro uložení ložisek v odlitcích převodových skříní. Samotná práce je rozdělena na dvě části. První pojednává o obrábění pomocí otočného stolu, druhá o obrábění bez otočného stolu „pomocí pevného stolu“. Také jsou zde zohledněny způsoby měření …
-
Konstrukce přesné vyvrtávací hlavy
Bakalářská práce se zabývá návrhem a konstrukcí přesné vyvrtávací hlavy. V první rešeršní části je řešena problematika vyvrtávání, vyvrtávacích strojů, vyvrtávacích nástrojů a jejich konstrukce a funkce. Druhá část obsahuje návrh a konstrukční výpočet přesné vyvrtávací hlavy. Výstupem práce je 3D …