Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 82 for “"Boundary layer control."”.
-
Ionization and boundary layer control.
… is to investigate the possibility of preventing boundary layer energy losses by ionizing selectively the boundary layer air. Electrostatic repulsion at the wall surface of the positive ions created in the method chosen to prevent molecular collision at the surface and the resulting energy losses. …
-
Submarine design optimization using boundary layer control
… design code. Optimization is done through boundary layer control analysis and through studies on the effect of blade loading magnitudes and profiles. Several hull form afterbody shapes are studied to improve the powering characteristics of a full stern submarine. The hydrodynamic analysis …
-
Experimental investigation of boundary-layer control by tangential injection
An experimental study of boundary-layer control by tangential injection in a two-dimensional flow is described and data representing eighteen different flows are presented. The data includes a variety of velocity profile types measured on plane and strongly curved surfaces in the presence of a …
-
Passive Turbulent Boundary Layer Control through 3D-Printed Dolphin Skin
… dolphin (Tursiops truncates) skin to mitigate boundary layer separation as a form of passive flow control, energizing the flow near the wall. A water tunnel generates a tripped turbulent boundary layer across a vertical test plate, and a rotating cylinder induces flow separation by creating an …
-
Direct numerical simulation of microjets for turbulent boundary layer control
… an array of MEMS slot jets in a turbulent boundary layer for the purposes of flow control. Initial studies were used to first ascertain the correctness of the model and give insight into the performance characteristics of the devices. To this end, a flow and geometric parameter study was …
-
Fluid dynamics of airfoils with moving surface boundary-layer control
The concept of moving surface boundary-layer control, as applied to the Joukowsky and NACA airfoils, is investigated through a planned experimental program complemented by theoretical and flow visualization studies. The moving surface was provided by one or two rotating cylinders located at the …
-
Moving surface boundary-layer control with application to autonomous underwater vehicles
Moving Surface Boundary-layer Control (MSBC) is a technique to delay separation and control circulation over bodies in fluid flow through momentum inj ection. In the past, rotating cylinders have been successfully used as the moving surface elements on both bluff and streamlined bodies. On …
-
Sounding Rocket Roll Control Through DBD Plasma Actuator Boundary Layer Control
… actuators alter the velocity of the air across control surfaces. The induced flow, directed tangential to the surface, inputs momentum to the boundary layer. This analysis examines the feasibility of a simplified boundary condition within computational fluid dynamic (CFD) simulations of a DBD …
-
Boundary Layer Control and Wall-Pressure Fluctuations in a Serpentine Inlet
In this thesis, the benefits of boundary layer control (BLC) in improving aerodynamic performance and engine stability were examined in a compact, serpentine inlet exhibiting flow separation. A 1/14-scale turbofan engine simulator provided the flow through the inlet. The inlet's mass flow was …
-
Numerical study of wingtip shed vorticity reduction by wing Boundary Layer Control
Wingtip vortex reductions have been obtained by Boundary Layer Control application to an AR=1.5 rectangular wing using a NACA 0012 airfoil. If wingtip shed vorticity could be reduced significantly, then so would induced drag resulting in improved cruise fuel economy. Power savings would be even …
-
Development of a boundary layer control device for tip clearence experiments in an axial compressor
A boundary layer control device was designed to change significantly the case-wall boundary layer thickness entering a large-scale, multistage axial compressor. The device was intended to double the boundary layer thickness in order to evaluate the influence of the inlet boundary layer in …
-
Aerodynamics and dynamics of bluff bodies in presence of the moving surface boundary-layer control
Moving Surface Boundary-layer Control (MSBC) was applied to several two dimensional bluff bodies using a high speed rotating cylinder as a momentum injecting device. Flow past a symmetric airfoil; a D-section; as well as square and rectangular prisms, representing a family of shapes with …
-
Numerical evaluation of corona discharge as a means of boundary layer control and drag reduction
<p>Problems of viscous drag reduction and boundary layer control have been and continue to be objectives of research for their economic impact and the enhancement of the flight characteristics of flying vehicles. Corona discharge is a new technique in this regard;The study of this technique …
-
Boundary-layer control of bluff bodies with application to drag reduction of tractor-trailer truck configurations
… of two fundamentally different concepts of boundary-layer control for the drag reduction of bluff bodies is studied experimentally. The methods are: (i) Moving Surface Boundary-layer Control (MSBC) involving momentum injection through one or more rotating elements (light hollow cylinders); …
-
Drag reduction of cube-van through boundary-layer control: wind tunnel experiments and prototype road tests
… on energy conservation as well as pollution control, there has been considerable interest in improving propulsive efficiency of road vehicles. Reduction in aerodynamic resistance is one aspect of it. Although aerodynamically contoured automobiles has become a standard design practice. Trucks …
-
Design and Numerical Evaluation of a Counter- Rotating Compressor in the Absence of Boundary Layer Control: Part II
… revitalized in research focused on the use of boundary layer control, again adding complexity and making the technology less than attractive to manufacturers. This thesis focuses on the design of a three-stage counter-rotating compressor without the benefit of boundary layer control. …
-
Design and Numerical Evaluation of a Counter- Rotating Compressor in the Absence of Boundary Layer Control: Part I
The purpose of this thesis was to design and evaluate a three stage counter-rotating compressor that employed well established design principles and technologies using a phased approach. The objective of the first phase was to generate the preliminary annulus shape and estimate the major parameters …
Page 1 of 5