Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 55 for “"Bulk Resistivity"”.
-
The use of the resistivity piezocone (RCPTU) for the geoenvironmental characterization of sulphide bearing tailings and native soils
… mine tailings have included the development of a resistivity piezocone (RCPTU) and improved water sampling technologies. The RCPTU measures the bulk resistivity of the soil, in addition to all other standard piezocone (CPTU) measurements. The bulk resistivity profile permits assessment of pore …
-
Investigation on Ammonium Perchlorate Based Electrically Controlled Propellants
… resulted in an apparent increase in the bulk resistivity of the propellant which was attributed to enhanced bubble/gas formation at the cathode. The increase in apparent bulk resistivity resulted in enhanced joule heating and a shift in ignition mechanism from predominately …
-
Detection and Quantification of Corrosion in Steel, Aluminum and Plastic Materials in Various Environments with Nondestructive Electrical Method
… method is to detect and quantify the surface and bulk corrosion and also to quantify the directional corrosion. The findings from this research study indicated changes in electrical resistance, capacitance, and resistivity in the bulk as well as the surface. In this study total of 31 specimens …
-
Controlled-source Electromagnetic Monitoring of Carbon Capture and Storage
… also been computed for various changes in the bulk resistivity of each of the two reservoirs, the Oaksville Sandstone and the Frio Formation. Several combinations of operating frequency, TX-RX offset and receiver depth have been highlighted because 1) the response they measure is above the …
-
Timing Resistive Plate Chambers with Ceramic Electrodes
… to radiation and chemical contamination. The bulk resistivity of these ceramics is in the range 10^7 - 10^13 Ohm cm. The bulk resistivity of the electrodes is the main factor determining the rate capabilities of a RPC, therefore a specifific measuring station and a measurement protocol has …
-
Layer-by-layer assembly of electrically conductive polymer thin films
… (~ 1500 é/sq), which corresponds to a bulk resistivity of 0.2 éâ cm for a 14- bilayer film that is 1.3 üm thick. Increasing the pH of the PAA-stabilized mixture and decreasing the pH of the PEI-stabilized mixture resulted in films with 70% transparency due to thinner …
-
Zirconium Oxide - Yttrium Oxide fO2/pH Electrode Behavior: The Role Of Temperature On Acid Durability, Charge Carrier Type And Nernstian Response
… than the zirconia ceramic, reduces the bulk resistivity and induces an error over the temperature ranges higher than the softening point of the glass. The glass also reduces durability of the ceramic. When the glass hydrates it produces zeolites, which grow primarily in the …
-
Durability Assessment and Service Life Prediction of Concrete in Extreme Aggressive Environment
… between chloride diffusion rates and concrete resistivity. By identifying these correlations and based on the target service life, the research aims to set appropriate thresholds for Surface Resistivity (SR) and Bulk Resistivity (BR) tests, which will be used to qualify concrete mixes used in …
-
Spark Plasma Sintering as a powder processing route for pre-alloyed Sm2(Co, Fe, Cu, Zr)17 permanent magnets
… work is based upon. A method of increasing the bulk resistivity of a REPM, Sm(Co, Fe, Cu, Zr)8.2 (henceforth referred to as Sm2(Co, Fe, Cu, Zr)17), through the addition of an electrically insulating material, CaF2, to form a rare earth composite permanent magnet is studied. The aim of increasing …
-
3d-printed lightweight wearable microsystems with highly conductive interconnects
… high curing temperature for achieving low resistivity (150 °C for obtaining nearly 2.069 x 10-6 .m in copper connects), which is not suitable for most of 3D printing filaments. Thisseriously limits the availability of many lightweight 3D printable materials in microsystem applications …
-
Characterization of electrical conductivity of carbon fiber/epoxy composites with conductive AFM and scanning microwave impedance microscopy
… two techniques. C-AFM was used to measure the bulk resistivity of IM7 fibers at (1.9 ± 1.1) x 10-3 Ω∗cm. Given that the uncertainty of these measurements is rather large, implementation of calibration experiments is needed. sMIM experiments revealed large nano-scale spatial variations in the …
-
A joint electromagnetic and seismic study of Arctic hydrates and fluid escape features, offshore Svalbard
… velocity anomalies observed within the GHSZ. Bulk resistivity estimates obtained from marine controlled source electromagnetic (CSEM) data are highly sensitive to the presence of both hydrate and free gas within the sediment pore spaces. The presence of hydrate leads to an increase in the bulk …
-
Unified Theory for Characterizing the Effects of Metallic Nanoparticles on the Performance of Microbial Fuel Cell and Cementitious Materials
… wires buried in the cement to investigate the bulk property changes. With electrochemical impedance spectroscopy, it was determined that the MFC and cement composite behaviors were controlled by the bulk resistivity of the two systems. Also each probe was represented as a capacitor-resistor …
-
Electrical resistivity of thin films of potassium
<p>The electrical resistivity of thin potassium films at 100°K has been measured as a function of thickness in the thickness range 148 to 1600 angstroms. The experimental results are in excellent agreement with Fuchs' theoretical predictions in the range 500 to 1600 angstroms and show that the …
-
Resistivity: relationship to penetrability of concrete and effect on zinc anodes in repaired concrete
Demands for using electrical resistivity techniques (surface and bulk resistivity) as an alternative to the rapid chloride penetrability test (RCPT) have been growing, for example by a number of transportation agencies in North America, to give an indication of the relative penetrability of …
-
Application of Electrical Resistivity Geophysical Monitoring for Detection of Preferential Flow
… of any remediation efforts. Electrical resistivity monitoring could be a useful tool to determine if infiltration is bypassing parts of the subsurface through preferential flow pathways and to better inform predictive models. The viability of this method was evaluated through simple …
-
Investigation of Concrete Electrical Resistivity as a Performance Based Test
… project was to identify the extent that concrete resistivity measurements (bulk and/or surface) can be used as a performance based lab test to improve the quality of concrete in Utah bridge decks. By allowing UDOT to specify a required resistivity, concrete bridge deck quality will increase and …
-
Constraints of Upper Mantle Thermodynamics with the Very Broadband Rheology Calculator and Magnetotelluric Observations
The electrical resistivity of the Earth’s mantle varies by more than five orders of magnitude (100 to 105 ohm-m). Parameters that impact the bulk mantle resistivity include mineral composition, temperature, pressure, melt fraction, and volatile content. Furthermore, the bulk resistivity depends on …
-
In Situ Measurements of Electron-Beam-Induced Surface Voltage of Highly Resistive Materials
… facilitates measurements of charge accumulation, bulk resistivity, effects of charge accumulation and depletion on yield measurements, electron-induced electrostatic breakdown potentials, radiation-induced conductivity effects, and the radial dispersion of surface voltage. Modeling and …
-
An Investigation of the Influence of Grain Boundaries on the Electrical Behavior of Polycrystalline ZrO2-CaO
… the specimen equivalent circuit. The effective resistivity of the boundaries was found to be much higher than the bulk resistivity while the total resistance of the boundary regions was comparable to the bulk resistance. These high resistivity boundaries were rationalized in terms of space …
Page 1 of 3