Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 21 for “"COMPRESSION WORK"”.
-
Characterization and system level study of air addition in a pilot ignited direct injection natural gas engine
… air over 300 bar, which may impose net compression work to the engine. Therefore, the system level implications were investigated by developing and characterizing a prototype compression system, and subsequently considering its compression work with the engine indicated efficiency. The …
-
ANALYTICAL AND EXPERIMENTAL INVESTIGATION OF TEMPERATURE-SWING INSULATION ON ENGINE PERFORMANCE
… show improvements both directly in indicated work and indirectly through reduced demand on the cooling system. Many experimental and analytical sources have shown reductions in heat losses to the combustion chamber walls, but converting the additional thermal energy to indicated work has …
-
Measurement of equation of state of compressed hydrogen and deuterium
… electron temperature and density.</p> <p>This work presents a full set of measurements of the thermodynamic properties for different laser intensity drives creating warm dense deuterium at various degrees of degeneracy and coupling. The measured electron densities and temperatures ranged …
-
A study of thermodynamic characteristics and predictive computer modelling of an air to water heat pump system
… was transferred to the refrigerant, 50 % by the compression work and 35% due to the heating of the refrigerant by the cylinder wall, and the remaining 15% (of the input power) was rejected to the cooling medium. The evaporator effectiveness was found to be about 75% and sensitive to the air …
-
Potential of controlling subcooling in residential air conditioning system
This work presents an experimental and simulation study of one way of improving residential air-conditioning (RAC) system performance by controlling subcooling. Instead of conventional superheat control at evaporator outlet, condenser subcooling is monitored and controlled and the corresponding …
-
Resin Infusion under Flexible Tooling
… and during resin infusion. The aim of the work was to examine the effect of the application of cycled loads equivalent to one atmosphere (i.e. the maximum load in a vacuum infusion process) on fibre beds to determine whether higher fibre volume fractions could be obtained. Mechanical …
-
Modeling advanced flash stripper for carbon dioxide capture using aqueous amines
… the energy consumption of CO2 regeneration and compression. The advanced flash stripper (AFS) proposed in this work provides the best energy performance among other alternatives. A systematic irreversibility analysis was performed instead of examining all the possible alternatives. The overhead …
-
INVESTIGATION ON THE POTENTIAL OF A CO2 CAPTURE SYSTEM, DOWNSTREAM OF THE AFTERTREATMENT SYSTEM FOR A HEAVY-DUTY ENGINE APPLICATION
… consumption and greenhouse gas emissions. This work investigates the potential of a CO2 capture system downstream of an aftertreatment system for a heavy-duty engine application. Amine absorption has been described as one of the most effective ways to capture CO2 from the exhaust for point …
-
System Simulation of Partially Premixed Combustion in Heavy-Duty Engines : Gas Exchange, Fuels and In-cylinder Analysis
… the knowledge gained from homogeneous charge compression ignition (HCCI) research. To extend the load range and thus reduce cylinder pressure rise rates, the fuel is directly injected during the compression stroke, instead of in the intake port as is common with HCCI. In contrast to …
-
Análise tribo-termodinâmica da aplicação de nanopartículas de Al2O3 como aditivo lubrificante em compressor hermético de refrigeração
… system can be improved by reducing the compression work by a particular technique for a specific heat removal rate. This study examines the effect of small concentrations of Al2O3 (50 nm) nanoparticles dispersion in the mineral oil based lubricant on the: viscosity, thermal conductivity, …
-
Continuous flash extraction of alcohols from fermentation broth
… ethanol, however the yields were extremely low. Compression work required ranged from 6.4 to 20.1 MJ/kg ethanol recovered from the gas stream in the case of 12% (v/v) ethanol in fermentor. The energy requirement for the 2% (v/v) extraction was 84MJ/kg recovered ethanol. The measured …
-
SPRAY AND COMBUSTION CHARACTERISTICS OF DIMETHYL ETHER UNDER VARIOUS AMBIENT CONDITIONS: AN EXPERIMENTAL AND MODELING STUDY
… properties that are potentially suitable for compression-ignition engine in automotive industry. There are many remaining challenges in understanding the combustion of DME, fuel handling and storage, specific fuel-oriented engine design in order to use DME effectively on transportation sector. …
-
LIDAR data classification and compression
… and functionality. LIDAR data classification and compression are therefore very important for managing, visualizing, analyzing and using this huge amount of data. Among the existing LIDAR data classification schemes, supervised learning has been used and can obtain up to 96% of accuracy. However …
-
Lignite gasification in gas turbine applications with co2 capture
This thesis work has evaluated the TopCycle technology for power production from lignite, integrated with drying, gasification and CO2-capture. The TopCycle concept is a high pressure, steam injected gas turbine with up to 50% steam in the flue gases. Within the frames of the thesis work the …
-
Lignite gasification in gas turbine applications with CO2 capture
This thesis work has evaluated the TopCycle technology for power production from lignite, integrated with drying, gasification and CO2-capture. The TopCycle concept is a high pressure, steam injected gas turbine with up to 50% steam in the flue gases. Within the frames of the thesis work the …
-
DEVELOPMENT OF A NEAR-ISOTHERMAL COMPRESSION PROCESS UTILIZING LIQUID PISTON TECHNOLOGY FOR TRANSCRITICAL CO2 CYCLE
… potential for further advancements. The compression process is often modeled as an isentropic process in which a significant portion of the work provided during compression is converted to heat, increasing the overall input power required. This inefficiency highlights the ongoing need for …
-
Potentials for COP increase in vapor compression systems
This work presents an experimental and numerical study of three different opportunities for COP increase in vapor compression systems: work recovery ejectors, condenser subcooling and increase of relative size of heat exchangers (HXs). Regarding work recovery ejectors, experimental results showed …
-
CFD Simulations and Thermal Design for Application to Compressed Air Energy Storage
… (water) is pumped into the lower section of a compression chamber, and the gas (air) is compressed by the rising liquid-gas interface. Important to the efficient operation of CAES is reducing the temperature rise during compression. The work input process for compressing the air requires two …
-
Modeling of a pilot plant for the CO2-reactive absorption in amine solvent for power plant flue gases
… large development. The objective of the present work is to model a pilot installation that should be built in the next few months. This pilot installation will be retrofitted in an existing coal-fired power plant in order to treat 5000 Nm³/h flue gas in two process trains. It is planed that 90% …
-
Numerical Investigations of sCO<sub>2</sub> Compressor Aerothermodynamics Using a Streamline Curvature Based Throughflow Method
… carbon dioxide (sCO2) has emerged as a promising working fluid for the Brayton power cycle, offering enhanced efficiency due to the high density and low viscosity of carbon dioxide (CO2) near the critical point. A critical component of the sCO2 Brayton cycle is the turbomachinery, namely the …
Page 1 of 2