Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 42 for “"Chip morphology"”.
-
Machining of additively manufactured titanium Ti-6Al-4V; cutting forces and chip morphology
… milling tests as an oblique cutting operation. Chip morphology has also been investigated to determine the mechanics of chip formation and its relationship to the properties of the AM titanium.
-
A Thermal-Mechanical Finite Element Analysis of Orthogonal Cutting for Normalized Steels
… cutting force, residual stresses and strains, chip morphology, and tool temperature. These results are summarized for each of the four cases and validated with experimental results found in literature. This study looks at optimizing the Johnson-Cook damage parameter D2 for steel materials in …
-
Microstructure -Level Machining Modeling of Ferrous Alloys
… conducted of the three materials. The measured chip morphology and machining forces were compared with the model predictions, and a good correlation between them was found. In addition, the microstructure-level model explained chip formation mechanisms and relationship between chip formation and …
-
Vibration Assisted Drilling of Carbon Fiber Reinforced Polymer and Titanium Alloy for Aerospace Application
… are attributed to high thermal load, continuous chip morphology, and poor chips evacuation efficiency. Vibration-assisted drilling (VAD) uses an intermittent cutting process to control the uncut chip thickness and chip morphology. VAD has potential advantages include low thermal load, high chips …
-
Chip Formation and Surface Integrity in High Speed Machining of Hardened Steel
… high temperatures the formation of saw toothed chips, and the high ratio of thrust to tangential cutting force components. Although a large volume of literature exists on hard turning, the change in machined surface physical properties represents a major challenge. Thus, a better understanding …
-
Drilling of carbon fibre reinforced plastic composites
… accuracy, workpiece surface integrity and chip morphology.
-
Analytical modeling of shear localization in machining processes and its effects on the tool-chip interface
… etc. Shear localization is the dominant chip formation mechanism in machining of these metallic components, limiting the cutting productivity due to high cutting temperature, rapid tool wear, and tool breakage. The machined surface integrity is also affected by shear localization with …
-
Numerical Modeling for Orthogonal Cutting of Brittle Materials
… A brittle cutting generally produces powder-like chips, fragmented and dusty debris, which can be hardly captured by common numerical models such as finite element method (FEM). To address the issue, this study investigates two different methods to model brittle materials cutting; smoothed …
-
Mechanics of machining zirconium-based bulk metallic glass
… In this thesis, a physics-based model of chip formation is developed for orthogonal cutting of Zirconium (Zr) - based BMG considering the process kinematics, material constitutive law, heat, and free volume evolution. The model predicts the segmented chip formation, oscillations of stress …
-
A Thermo-Mechanical Force Model for Machining Hardened Steel
… of hard machining, the fundamental aspects of chip formation, tool wear and life is explored through a detailed investigation. It was confirmed that the ball milling of hard materials produce segmented saw toothed chips even at low chip loads for specific cutting conditions. It was noticed that …
-
DYNAMIC FEED RATE SCHEDULING IN MESO-SCALE MILLING PROCESSES
… predictions in terms of cutting forces and chip morphology. Based on the contact forces obtained from the simulation, tool stress analysis and breakage prediction are then advanced for meso-scale shoulder milling processes. Finally, a stress based feed rate scheduling algorithm is formulated …
-
A STUDY ON STRAIGHTNESS CONTROL IN DEEP HOLE DRILLING OF INCONEL-718
… edge radius, quantification of the effects of chip morphology on the drilling thrust force and the predictive straightness deviation modelling considering the effect of machine set-up parameters. The predicted results were found to be in good agreement with the experimental hole straightness …
-
MACHINABILITY AND MICROSTRUCTURE STABILITY DURING THE MACHINING OF PURE COPPER AND TITANIUM PROCESSED BY EQUAL CHANNEL ANGULAR PRESSING
… the machinability cutting forces, tool wear, chip morphology, and surface roughness were studied using different cutting conditions. Tungsten carbide (WC) and polycrystalline diamond (PCD) cutting tools were utilized for turning the copper workpieces while only PCD was used for titanium. …
-
Influence of Dynamic Behaviour of Materials
… during metal cutting) on machinability (i.e., chip morphology, tool wear and surface finish) has been investigated in ferrous alloys with a wide range of matrix and volume fraction of second phase particles. With the increase of cutting speed, there is change in the tribological phenomenon at …
-
Influência da refrigeração criogênica na vida da ferramenta de PCBN e na integridade superficial do aço ferramenta D6
… stress, surface roughness, tool wear and chip morphology have been the output variables. The results have showed that the cryogenic cooling has been able to reduce tool wear and give better surface roughness compared to the dry machining within the category N4. Higher values of compressive …
-
Characterization, cutting mechanisms and machinability of lead-free brasses
… material characterization, cutting mechanisms (chip breaking), as well as the assessment of the machinability of leaded and lead-free brass alloys, widely used in industrial applications for the fabrication of final brass component (bolts, nuts, hydraulic fittings, valves etc.) by …
-
Finite element modelling (including material grain refinement prediction) when turning advanced aerospace alloys
… such as cutting forces, temperatures and chip morphology, the FE models were extended to enable prediction of grain size distribution due to dynamic recrystallisation (DRX) of workpiece microstructure following machining. This was accomplished by developing a VUMAT user customised …
-
Performance Evaluation of Minimum Quantity Lubrication (MQL) When Machining High-Performance Materials
… measure surface roughness, tool contact length, chip morphology, and flank wear. The present study provides insight into the cutting performance of coated carbide tools. To improve the machinability of magnesium alloys, the study also investigated tool wear mechanisms, surface roughness, and …
-
Hole making performance and damage mechanisms of carbon fibre reinforced polyetherketoneketone (CF/PEKK)
… on the resulting thrust force, temperature and chip morphology, hole delamination/microstructural damage and material removal mechanisms, have been thoroughly investigated and wherever possible, compared with that of the conventional CF/epoxy. Multi-objective optimization has been conducted to …
-
Torneamento do aço-ferramenta AISI D6 temperado e revenido nas condições seco, jorro e LN2: uma análise técnico-econômica
… As output variables cutting tool wear and chip morphology were monitored. The technical and economic analyses were performed based on the cost/hour related with the consumption of cutting tool, cutting fluid, electric energy and cutting fluid disposal. It was concluded that the dry …
Page 1 of 3