Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 893 for “"Combustor"”.
-
Gas Turbine Combustor Wall Cooling
… need for better methods of cooling gas turbine combustors and a review of current cooling techniques have been presented. Three cooling methods are investigated: (a) Full Coverage Discrete Hole Film Cooling (Effusion), (b) Impingement/Effusion Hybrid Cooling Systems, and (c) Transpiration …
-
Methods for Decarbonized Aeroengine Combustor Design
… promise ultra-low emissions. Future aeroengine combustors operating in highly swirled premixed mode with hydrogen/air mixtures are central to this paper. Prior to the implementation and design of such systems, premixed combustion conditions must be correlated with gas turbine engine performance …
-
Combustor simulators for scaled turbine experiments
<p>Gas turbine combustors employing a single lean combustion stage represent the next generation of design for reduced NO<sub>X</sub>emissions. These lean-burn combustors rely on swirl-stabilised flames resulting in highly non-uniform outflows. Non-uniform conditions adversely affect high-pressure …
-
Improved understanding of combustor liner cooling
<p>Heat management is an essential part of combustor design, as operating temperatures within the combustor generally exceed safe working temperatures of the materials employed in its construction. Two principal methods used to manage this heat are impingement and film cooling.</p> <p>Impingement …
-
Mesoscale, porous media heat recirculating combustor.
… of the mesoscale, heat recirculating combustor design were determined experimentally with a system of 125 cm3 using methane fuel. The combustor featured an annulus around the combustion chamber to preheat reactants and reduce heat loss to the surroundings. The presence of PIM in the …
-
Numerical Investigation of a sub-1 kN Turbojet Combustor: Quantification and Reduction of the Combustor Pressure Loss
… and aerodynamic behavior of a small turbojet combustor to determine total pressure loss and its impact on specific thrust and thrust-specific fuel consumption. Manufacturer specifications were used to estimate key thermodynamic states, which served as boundary conditions for a cold-flow CFD …
-
Emissions from a gas-burning pulse combustor
The pulse combustor has a number of attractive features for heating applications. These include simplicity of construction, compactness for a given heat input rate, enhanced exhaust gas heat transfer and most importantly low CO and NOx emissions. With more stringent air quality and emissions …
-
CFD Modelling of Generic Gas Turbine Combustor
… a simple yet accurate model, for a generic combustor of industrial interest, that may be tested in a relatively short time and that yields reliable results. An important topic is here to perform grid sensitivity studies to make sure that the model yields mesh independent results. Another …
-
Optimisation of Low NOx Hydrogen Micromix Combustor
… necessitates the modification of conventional combustors to accommodate hydrogen combustion. The concept of micromix combustion has emerged as a promising and dynamic solution to address the challenges of safe hydrogen combustion. Aachen University has conducted extensive studies and …
-
Investigation of air control on chunkwood combustor
… and high emissions. A prototype chunkwood combustor was installed and tested. The basis for controlling heat output, was the modulation of air supplied to the primary and secondary combustors. Exhaust gas CO and CO₂ concentrations, combustor efficiency, and useful heat output were measured. …
-
Primary Development of a Propane Air Combustor
<P> The design, and construction of a combustion chamber was undertaken, and the basic considerations, design steps and calculations are described. The preliminary testing consisted of measurements of flame temperature, flame tube wall temperature, and flame tube exit plane temperature. A …
-
The effect of tailpipe length on combustor stability
Electronic Thesis or Dissertation
-
Clean Burning Wood Combustor Using Rich Quench Lean
… develop a clean burning residential wood burning combustor. Currently, the Environmental Protection Agency (EPA) requires PM emissions from residential wood heaters to remain within 2.5 g/hr, and further reductions are projected to take place in coming years. Wood combustion also produces harmful …
-
Advances towards a pressurised rotating fluidised bed combustor
… were conducted in flow visualisation rigs and a combustor designed to accommodate a distributor 200mm diameter and 80mm axial length. Ancillary experiments were conducted in a 6" diameter conventional fluidised bed. The investigations encompassed assessment of; fluidisation and elutriation, coal …
-
Multi-fidelity strategies for lean burn combustor design
In combustor design and development, the use of unsteady computational fluid dynamics (CFD) simulations of transient combustor aero-thermo-dynamics to provide an insight into the complex reacting flow-field is expensive in terms of computational time. A large number of such high-fidelity reactive …
-
Development of an Atmospheric Fluidized Bed Combustor (AFBC)
The relatively recent interest in the U.S. in the development of atmospheric fluidized bed combustion (AFBC) has been preceded by two main factors. First of these is the ever present problem of acid rain and growing public support for cleaner burning fossil fuels. Second is the increasing demand on …
-
Wood pellets combustion in a fixed bed combustor
… time. The wood pellets combustion in a fixed bed combustor with the boiler capacity of 20 kW were tested with several parameters including Power, excess air (EA), the split ratio (SR) and grate area (GA). In this work, the Taguchi method was applied to conduct the experiments. From these …
Page 1 of 45