Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 49 for “"Compression members"”.

  1. Axially loaded stainless steel compression members

    … formed and hot rolled, annealed stainless steel members undergoing axial compression forces. Research related to the subject will be summarized as well as available design practice codes, from where applicable expressions will be investigated and used to perform practical examples.

    gatech Repository record for Axially loaded stainless steel compression members (opens in a new tab)

  2. A study of single angle compression members

    … capacity of a specific group of single angle members. A review of existing literature and techniques was presented. Laboratory compression tests were performed on 22 angle members of four different sizes and two different lengths. Additional tests were performed to determine the yield strength …

    portland-state Repository record for A study of single angle compression members (opens in a new tab)

  3. Cold-formed steel compression members with perforations

    … strength of perforated cold-formed steel (CFS) members subjected to axial compression loading.</p> <p>Cold-formed steel sections are widely used nowadays as primary and secondary framing members in low-rise steel buildings. Although CFS members are essentially thin-walled framing elements, with …

    mcmaster Repository record for Cold-formed steel compression members with perforations (opens in a new tab)

  4. Resistance Factor for Cold-Formed Steel Compression Members

    … strength reduction factor for cold-formed steel compression members can be increased above its current value of Ï c = 0.85, which was established by the LRFD Cold-Formed Steel Design Manual (1991) on the basis of 264 column tests. The resistance factor in the Canadian code for cold-formed steel …

    vt Repository record for Resistance Factor for Cold-Formed Steel Compression Members (opens in a new tab)

  5. Buckling Resistance of Single and Double Angle Compression Members

    … and inelastic buckling resistance of compressive members with single angle and back-to-back double angle cross-sections with end conditions representative of those commonly used in steel construction. The first contribution develops an elastic buckling solution for members with asymmetric …

    ottawa-retro Repository record for Buckling Resistance of Single and Double Angle Compression Members (opens in a new tab)

  6. Laterally loaded wood compression members : finite element and reliability analysis

    … for the general prediction of failure of wood members in bending or in combined bending and axial compression. Both instability and material strength failures are included. The program is verified using available analytical and test results. A good agreement with the results predicted by this …

    ubc Repository record for Laterally loaded wood compression members : finite element and reliability analysis (opens in a new tab) Download PDF for Laterally loaded wood compression members : finite element and reliability analysis (opens in a new tab)

  7. The Effect of Lateral Confinement on The Behavior of Axially Loaded Concrete Compression Members

    Made available in DSpace on 2014-12-08T23:57:15Z (GMT). No. of bitstreams: 1 6915276.pdf: 7126435 bytes, checksum: a43d7fe64a4374882f011cf6c118d885 (MD5) Previous issue date: 1969

    uiuc Repository record for The Effect of Lateral Confinement on The Behavior of Axially Loaded Concrete Compression Members (opens in a new tab)

  8. Behaviour modification of space trusses

    … to be limited by the failure of a new critical members. Because of high redundancy, and due to practical constraints in selecting member sizes, only a portion of the member strength is used. Attempts have been made to utilize the remaining strength of the members by providing a means of …

    concordia Download PDF for Behaviour modification of space trusses (opens in a new tab)

  9. Development of design criteria for ferritic stainless steel cold-formed structural members and connections

    … criteria needed for the design of structural members cold-formed from certain ferritic stainless steels. The Allowable Stress Design method as well as the Load and Resistance Factor Design method receive attention. The ferritic stainless steels under consideration are: Types AISI 409 and 430 …

    must-thes Repository record for Development of design criteria for ferritic stainless steel cold-formed structural members and connections (opens in a new tab)

  10. Tensegrity structure for low-cost solar photovoltaic racking and its potential for bifacial PV array

    Tensegrity, a structure made of rods as compression members and cables (or strings) as tensile members, is evaluated as a lightweight, low-cost solution for solar photovoltaic (PV) racking. A novel algorithm is developed to integrate the deployable tensegrity structure into the bestpractice …

    ttu Repository record for Tensegrity structure for low-cost solar photovoltaic racking and its potential for bifacial PV array (opens in a new tab)

  11. Experimental Determination of Post-buckling Performance of Steel Angles

    … testing program was conducted to determine the compression member performance in post-buckling region. These results are compared with an analytical computer program developed by Portland State University under Bonneville Power Administration Contract 79-80BP 24005. The paper presents the …

    portland-state Repository record for Experimental Determination of Post-buckling Performance of Steel Angles (opens in a new tab)

  12. Axial load capacity of cold-formed steel sections.

    Cold-formed steel strut purlins are important compression members in metal building wind bracing systems. They are generally located under the roof panel either in the braced bay or between the end wall and the first wind-braced bay in the building. Cold-formed Zee and Cee sections are typically …

    oklahoma-thes Repository record for Axial load capacity of cold-formed steel sections. (opens in a new tab)

  13. Probabilistic Based Design of FRP Structures

    … based design procedure for concentrically loaded compression members and simply supported beams of fiber-reinforced polymeric (FRP) composite materials. Resistance factors for use in an LRFD format are developed for columns for both flexural buckling and local buckling of doubly symmetric …

    utk-theses Repository record for Probabilistic Based Design of FRP Structures (opens in a new tab)

  14. Lightweight Tensile Restrained Structures

    … may be significantly improved by restraining the compression members laterally by tensile membrane. Both numerical and experimental investigations have been performed to understand the structural behaviour of TSSs. In DCCSs, cable restrained compressive elements consisting of discretized struts …

    nus Repository record for Lightweight Tensile Restrained Structures (opens in a new tab) Download file for Lightweight Tensile Restrained Structures (opens in a new tab)

  15. Failure and crippling of graphite-epoxy stiffeners loaded in compression

    … crippling of thin-walled open section prismatic compression members are presented. Twenty-four specimens were tested, 13 of which were channel sections and the other 11 were zee sections. Three specimens were made of 2024-T3 aluminum. The remaining 21 specimens were made of AS4-3502 …

    vt Repository record for Failure and crippling of graphite-epoxy stiffeners loaded in compression (opens in a new tab)

  16. Assessment of the long term performance of repaired reinforced concrete.

    … structural behaviour of repaired concrete members. A comparison is also made between the performance of these repair materials with a plain concrete mix of similar strength and stiffness. The following generic repair materials were used: a high performance non-shrinkable concrete, a mineral …

    sheffield-hallam Download PDF for Assessment of the long term performance of repaired reinforced concrete. (opens in a new tab)

  17. Kinematic Analysis of Tensegrity Structures

    Tensegrity structures consist of isolated compression members (rigid bars) suspended by a continuous network of tension members (cables). Tensegrity structures can be used as variable geometry truss (VGT) mechanisms by actuating links to change their length. This paper will present a new method of …

    vt Repository record for Kinematic Analysis of Tensegrity Structures (opens in a new tab)

Page 1 of 3