Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 58 for “"Computed torque"”.
-
ENHANCEMENT OF COMPUTED-TORQUE CONTROL FOR ROBOT MANIPULATORS
… developed based on the basic structure of the computed-torque control (CTC) algorithm, which has a wide popularity in modern robot control theories. Hence, the core of the dissertation can also be interpreted as an enhancement of the CTC scheme for robot manipulator. Robustness was introduced …
-
Computed torque control of a differentially driven automated guided vehicle
Investigates the suitability of a computed torque control scheme for the CONCIC II prototype AGV developed at Concordia University's Centre for Industrial Control.
-
Dynamic modelling and computed torque control of flexible-joint thrust vector control system
… designed and also an alternative that includes Computed Torque Control Law (CTCL) action. It is confirmed, however, that these designs lack robustness even though such a control law gives better performance than the classical control law arrangement. This motivates the last major control law …
-
Validation of a virtual prototyping method using computed torque and ILC as controllers on a parallel robot
… method. At this stage we also calculated a computed torque controller that is used later when comparing the performance of the macro-generated dynamic model to the actual robot. The rest of our thesis shows how the new macro replaces both the hand-calculation and manualentry methods of …
-
Neuro feedback linearisation in the control of robotic manipulators
… different control techniques, in particular, the computed-torque control technique and the state feedback linearization. A neural network control approach based on the state feedback linearization technique is also proposed and studied.A two-link manipulator has highly nonlinear dynamic …
-
DESIGN AND CONTROL OF A 3 DEGREE OF FREEDOM ROBOT
… programming is done using Borland C++. PID and computed torque control laws are implemented for small angle motions. For large angle motions the control laws are modified to overcome the limitations of actuator saturations, bandwidth and velocity. Based on the experiments, the performance of the …
-
Line-of-sight-stabilization and tracking control for inertial platforms
… stabilization and tracking are proposed: (i) computed torque control and (ii) sliding mode control using the recent SuperTwisting Algorithm (STA) combined with a High-Order Sliding Mode Observer (HOSMO). Simulations using data from a simulated vessel allow us to compare the performance of the …
-
Dynamics and control of light weight flexible manipulators.
… Even though collocated control such as the computed torque method leads to asymptotic stability in the case of rigid link manipulators, the end point of the single link flexible manipulator has shown sustained oscillations under this type of control. In order to improve the performance of …
-
Comparison of robotic positional control strategies
… plus integral plus derivative (PID) method, computed torque method, resolved motion rate control (RMRC) method and the model-referenced adaptive control (MRAC) method. These schemes were representative of three categories of robotic positional controllers - Joint Space control, Cartesian …
-
VISION BASED SERVO CONTROL OF A 3-DOF ROBOT
… The joint feedback controller adopts a modified computed torque control law (dynamic model based) that provides control torques to the joint motors of the manipulator. From simulation and experiments it is observed that the modified computed torque control law results in better end-effector …
-
Prosthetic legs output feedback control via variable high gain observers
… full-state feedback scheme is implemented using computed torque plus a PID controller, and then a high gain observer is designed to estimate the system states. We propose the implementation of a high gain observer (HGO) to estimate the prosthesis joint velocities with a time-varying HGO gain …
-
Modeling, Control and Locomotion Planning of an Anguilliform Fish Robot
… the mathematical model of the robotic fish. Computed torque control and sliding model control are proposed to deal with different scenarios. Three locomotion patterns are investigated by experiments and simulations. Relations among swimming speed, turning radius, and related parameters are …
-
Adaptive rapid tracking by a 3 DOF robot manipulator
… of the manipulator system. This is followed by computed torque to approximately linearize the non-linear system using the estimated parameters. Because the approximately linearized plant is time-varying and has imprecisely-known parameters, and for the purpose of rapid tracking, adaptive control …
-
Real-time path-constrained trajectory planning for robot manipulators with energy budget optimization
… to minimize the cost function in real time. A computed torque linearization scheme is considered to simplify the Newton method. The solution is also formulated in the manipulator task space permitting to be used with a kinematic control scheme, which is fundamental since many industrial …
-
Adaptive control and parameter estimation of dynamically mismatched robotic manipulators
… performance when compared to a non-adaptive computed torque controller. A step change in the payload mass is also tracked and properly identified by the adaptive controller.</p>
Page 1 of 3