Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 34 for “"Conditioning Time"”.
-
Zero-conditioning time concept in flotation
… That ensures that the collector is at the right time at the point where it is needed to facilitate the attachment of the particle to the bubble. It is generally accepted that flotation with amines is very rapid and that only a short conditioning time is required in such a cationic flotation. This …
-
Effects of Residual Moisture and Zero Conditioning Time on Maximum Theoretical Specific Gravity
… produced mixes; residual moisture and a short conditioning time. To test the effects of residual moisture samples of slag aggregate were saturated with water for a period of time then heated allowing some of the water to evaporate and then mixed with other aggregates and binder. Samples were …
-
CHEMICAL MECHANICAL POLISHING PAD PROFILE OPTIMIZATION
… rate occurred. In this report, various pad conditioning parameters and their important characteristics for the pad wear during conditioning are explored. To maintain a uniform pad profile, current conditioning recipe has to be modified. The report demonstrated a successful attempt in …
-
Carbon Dioxide Capture From Fossil Fuel Power Plants Using Dolomite
… were weight of calcium oxide and sintering time of the sample. The dolomite materials investigated were from two sources Alfa Aesar and Specialty Minerals. The prepared sorbent, after conditioning, is in the oxide form and can adsorb CO2 to form the carbonate and be regenerated back to the …
-
Flotação por ar dissolvido para os minerais quartzo e feldspato utilizando coletores catiônicos
… which may occur in pockets with metric to centimetric dimensions or as millimetric to sub millimetric intergrowths. The correct physical liberation of the mineral of interest, in case of intergrowths, requires an appropriate particle size, acquired by size reduction operations. The method for …
-
Evaluation of the degree of blending of Reclaimed Asphalt Pavement (RAP) binder for warm mix asphalt
… other varying pre-paving conditions like mixing time, mixing temperatures, conditioning time, and WMA type. A comparison between fine and coarse extracted samples immediately showed that the binder from virgin and RAP aggregate is not similar and is not fully blended. Degree of blending proved to …
-
Variation of the mechanical properties of the natural rubber used in bridges’ bearings and seismic isolators in Canada
… of mechanical properties due to source, age, conditioning duration, and test temperature as well as the frequency of cycling. Specimens from each source of natural rubber are conditioned at different temperatures, namely 23ºC, -8ºC, and -30ºC, for different durations, going from 1 hour to 28 …
-
The influence of conditioning on internal checking of high-temperature dried Pacific Coast hemlock
… study was to evaluate the effectiveness of steam conditioning immediately after drying to reduce internal checking resulting from high-temperature drying of Pacific Coast hemlock lumber. Three different levels of conditioning time, 2, 4 and 6 hours, were carried out on 2 inches wide by 4 inches …
-
The Effect of Feed Manufacture Techniques on Pathogen Reduction and Feed Nutrient Value
… feed manufacture techniques, such as varying conditioning times and new equipment, can affect pathogen mitigation, feed manufacture metrics, amino acid digestibility, and enzyme recovery in feed. Feed hygienics are of increasing importance in providing safe feed to animals, and ultimately safe …
-
Effects of Warm Mix Additives and Dispersants on Rheological, Aging and Failure Properties of Asphalt Cements
… for asphalt cement employ insufficient aging and conditioning times prior to testing and low strains during the actual test which are insufficient to predict asphalt performance, especially if the materials are modified with additives such as those used for warm mix technology. However, slightly …
-
Determining the flexural strength of asphalt mixtures using the Bending Beam Rheometer.
… to investigate the joint effect of temperature, conditioning time and loading rate, on the measured strength of three different mixtures, by using a 23 factorial design The third set consists in tests performed on a second group of eight mixtures tested at three temperatures. The different test …
-
ENHANCED SEPARATION PERFORMANCE FOR FRACTIONALLY LIBERATED MATERIALS USING THE HYDROFLOAT™ PROCESS TECHNOLOGY
… flowrate, air flowrate, collector dosage and conditioning time on the efficiency and optimization. Therefore, this study focuses on the development and validation of a standard testing procedure for an 82-mm diameter laboratory scale HydroFloat™ unit designed and manufactured by Eriez, …
-
Evaluating Steam Conditioning Manipulations and Grain Expressed Enzymes Effects on Feed Manufacturing Metrics, Feed Hygiene, Broiler Performance, and Bone Mineralization
… both short-term (ST) and long-term (LT) steam conditioning, to determine the effects of antimicrobial inclusion and conditioning temperature variations on feed manufacturing metrics (EXP1) and the mitigation of a Salmonella surrogate (EXP2). A split-plot design was utilized where ST (10s) or LT …
-
Research of Order Processing Capabilities for Oscillatory Signals in Rotating Equipment
… data by revolutions would also be beneficial for time domain analysis.This paper explores the need for order processing, reviews similar methods employed in other data acquisition applications such as blade tip timing, and discusses options for making order processing possible for any oscillatory …
-
Coarse Particle Flotation of Coarse Gold and Gold-bearing Ore by Fluidized-bed-flotation
… of several key process variables including conditioning time, collector dosages, aeration rate, elutriation water rate, feed rate and feed solid content. Initially, collector dosages and conditioning times were optimized by varying one factor at a time. After a detailed optimization program, …
-
Evaluation of rheological master curve parameters for the practical specification grading of Canadian asphalt binders
… binders, resulting in significant material and time consumption, as well as extended labour. Moreover, the EBBR test requires three days of conditioning time. Therefore, current research is focused on developing simplified methods that use less material and less time while ensuring precision and …
-
Moisture Uptake and Loss of Geosynthetic Clay Liners from a Silty Sand Subgrade Under Isothermal Hydration and Thermal Cycles
… sand subgrade of varying density, compaction conditioning time, and grain size distribution due to silt aggregation are reported. For the isothermal tests, the columns were stored at 25±4°C for four weeks. For cyclic tests, the column airspace was subjected to thermal cycles up to 60°C for the …
-
Optimization of spodumene flotation with fatty acid collectors
… from the 1960s first reported that high density conditioning improved TOFA flotation performance, but collector properties and adsorption behaviour throughout conditioning remain poorly understood. Based on these challenges, the objective of this project was to investigate the impact of three …
-
Cold In-Place Recycling with Expanded Asphalt Mix (CIREAM)
… Indirect tensile strength testing with moisture conditioning was used to assess the effects of asphalt cement type (80, 300 pen grades and polymer modified asphalt), conditioning time, and additives such as Portland cement, foam stabilizers, polymers and fibers. Uniaxial cyclic compression with …
-
Soft Nanoparticle Flotation Collectors
… on glass bead surfaces decreased with increased conditioning time; (2) large nanoparticles aggregates were detected in flotation pulp as well as on bead surfaces; and, (3) dislodged soft-shelled PS-PB particles left polymeric patches, we call footprints, on the glass bead surfaces. Indeed, the …
Page 1 of 2