Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 45 for “"Copper particles"”.
-
Synthesis of Nanomaterials for Optical and Catalytic Studies
… the Cu source was developed to prepare metallic copper nanoparticles NPs with sizes that can be tuned. Copper particles with sizes ranging from 46 to 90 nm were synthesized and a clear correlation with plasmon absorption was obtained. In order to study the application and extend the usability of …
-
Μελέτη απλών και σύνθετων επικαλύψεων ψυχρού ψεκασμού: μικροδομή, μηχανισμός συναπόθεσης, τριβολογία και αντοχή σε διάβρωση
… nozzle and produces a supersonic gas flow. Spray particles are accelerated to a high velocity (typically 300-1200 m/s) and are deposited at a temperature well below their melting temperature. Initially in this research, three different materials with important industrial applications were cold …
-
The measurement of flame propagation within an electrostatic particulate system
… mixtures with various concentrations of 53-63mum copper particles acting to quench the flame. At low copper concentrations the burning velocity was increased. However, as copper particle concentration was increased the measured burning velocity quickly dropped below the burning velocity of similar …
-
The role of pulmonary intravascular macrophages (PIMs) in porcine reproductive and respiratory syndrome virus (PRRSV) infection in pigs
… of SOA at 24 and 48 HPI. Pulmonary clearance of copper particles was conducted to measure the effect of PRRSV infection on PIM function in vivo. Pigs were infused intravenously with 3% copper phthalocyanine tetrasulfonic acid (0.2 ml/kg) in saline 30 minutes prior to necropsy after 3, 7, 10, 14, …
-
Thermomechanical cycling investigation of CU particulate and NITI reinforced lead-free solder
… to test runs on the same solder matrix with Copper particles and then the SMA, Nickel- Titanium wire as reinforcements.
-
The effect of aging treatment on the microstructure and properties of copper-precipitation strengthened HSLA steel
… part due to the precipitation of fine coherent copper particles formed during a quench and aging heat treatment. HSLA-100 is being developed to meet the strength and toughness requirements of HY-100 but can be easily welded without preheat, thereby reducing fabrication costs. This investigation …
-
Preparation and properties of micro- and nanocomposites based on high density polyethylene
… different fillers were considered: micrometric copper particles, nanometric carbon blacks (CBs) and multiwalled carbon nanotubes (MWCNTs). In the first part of this dissertation, the fracture behaviour of PE-CB composites was investigated via the Essential Work of Fracture (EWF) approach by …
-
Cross-Linked PDMS Expansion Due to Submersion in Liquid and Supercritical CO2
Characterization of micro/nano-copper particles impregnated Polydimethylsiloxane (PDMS) submersed in supercritical carbon dioxide (scCO2) was studied. The purpose of this investigation was to advance micro-corrosion sensor technology utilizing PDMS and micro-metal particle composite as the sensing …
-
Production of Co, Ni, and Cu nanoparticles by hydrogen reduction
In this thesis, production of Co, Ni, and Cu nanoparticles by hydrogen reduction of metal chlorides in gas phase was studied. Nanoparticles have unique properties not found in bulk or micron-scale materials. These enable new products or reduced use of raw materials. Metal nanoparticle production …
-
Ultra-Wideband Monocone Antenna and V2X Testing
… with low-cost plastic material and sprayed with copper particles for rapid and cost-effective fabrication. The diameter and height of the antenna are 148 mm and 26.695 mm, respectively. The efficiency is measured to be over 87.97 % throughout the frequency bands of interest. Proceedings from …
-
Air-breathing magneto-deflagration thruster for very low Earth orbit
… in the size and elemental mapping of ablated particles. It is found that copper particles are much smaller (0.2-0.8 µm) than their aluminum and iron counterparts (2-10 µm). Mass loss measurements are taken using a microbalance at increasing values of n[subscript e]/n[subscript g], the ratio of …
-
Kompozitų su nanodariniais elektromagnetiniai tyrimai /
… sensors and etc. Often a few different nanoparticles are combined with nanocarbons to find new composite materials for different applications. The aim of this study is to measure and analyze dielectric and electrical properties at different frequencies of composites with multilayer carbon …
-
SIMULATIONS OF SINGLE METALLIC PARTICLE IMPACTS ONTO POLYMERIC SUBSTRATES FOR INSIGHTS INTO COLD SPRAY ADHESION AT COMPOSITE MATERIAL INTERFACES
… single 20-micron diameter spherical metal (copper) particles and polymer (polyetheretherketone) substrates under cold spray-relevant impact conditions. Analysis of FEA simulations centers on initial impact processes parameterized by particle impact velocity and particle impact temperature, …
-
Novel substrates for improved cooling of power electronics
… phase cooling was integrated with direct bonded copper power substrates by sintering copper particles directly onto the back side to allow for evaporative two phase cooling. The work experimentally investigated the impact of the thickness of the copper microporous layer as well as its size …
-
Cellulose based materials as a template for the synthesis of copper nanoparticles for antimicrobial applications
Copper has been used as a broad-spectrum biocide for centuries, showing effective antimicrobial performance against bacteria, fungi and viruses. Among various forms of copper, copper nanoparticles is attracting particular attention because of its high surface area and crystal morphology that will …
-
Vanadium dioxide-based materials for potential thermal switching applications
… (k_(elec.)) in the metallic state, nano-sized copper particles were added to the VO2 system with a subtle amount variation ranging from 3at % to 5 at%. Results show that a composite with 5 at% Cu (copper) addition exhibited the largest increase in thermal conductivity (k) in the metallic state. …
-
Fluid Mechanics of Micro Cold Spray Direct Write Process
… coatings applications. In this process, metal particles of diameter 5 μm to 50 μm are accelerated to a very high velocity (>500 m/s) and are deposited on substrates. Based on principles similar to cold spray process, we have developed a novel direct write process known as the Micro Cold Spray …
-
Fluidization of nanoparticles
During the past decade, nanoparticles (1-100 nm) and nanocomposites have become the focus of many studies due to the unique properties of nanostructured materials that make them attractive for various applications. Due to their atomic and molecular interactions, nanoparticles and nanocomposites …
-
Experimental and computational analysis of laser sintered three-dimensional wick structures for thermal management applications
… types of wick structures – one manufactured with copper particles and the other with stainless-steel 316L particles - are considered. Existing manufacturing capabilities pose significant barriers in terms of manufacturing time and wastes, to the creation of wick structures for efficient heat …
Page 1 of 3