Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 34 for “"Cryomilling"”.
-
Metal based reactive nanocomposites prepared by cryomilling
… milling at the liquid nitrogen temperatures, or cryomilling, which enables mixing aluminum with materials that are unstable or difficult to process at room temperatures. Two types of composite materials are prepared and characterized: Al-I2 and Al-hydrocarbon (where wax, low density polyethylene …
-
Development Of Nitrogen Concentration During Cryomilling Of Aluminum Composites
… concentration increased as a function of cryomilling time up to 72hours. A greater nitrogen concentration resulted in an enhanced thermal stability of the nanocrystalline aluminum phase and a resultant increase in hardness. The distribution of the nitrogen-rich dispersoids may be estimated …
-
Cryomilling of Aluminum-based and Magnesium-based Metal Powders
… Ball milling at cryogenic temperatures (cryomilling) is more effective in this capacity due to the low temperature by slowing recovery and minimizing diffusion distances between different components. Nanostructured metals are of interest because of their unique physical and mechanical …
-
Cryomilling and Spark Plasma Sintering of 2024 Aluminium Alloy
… milled in slurry formed with liquid nitrogen. Cryomilling takes advantage due to low temperature of the liquid nitrogen that either suppresses or limits recovery and recrystallization and leads to finer grain structure faster. In addition cryogenic milling does not require use of process …
-
Effect of cryomilling on zinc sulfide effectiveness as antibacterial substance for burn wound healing
… the effect of the manufacturing process cryomilling on the antibacterial effectiveness of a novel antibacterial agent ZnS. ZnS nanoparticles are getting attention for their potential antibacterial properties due to the fact that release of Zn ions has demonstrated promising preliminary …
-
Deformation mechanisms in bulk nanostructured aluminum obtained after cryomilling and consolidation by spark plasma sintering
… (nc)/ultrafine (UF) aluminum was produced after cryomilling and spark plasma sintering consolidation process. The samples obtainedwere plastically deformed in uniaxial compression. We show that there is a significant fraction of plastic strain (11%) that can be recovered after unloading. …
-
Development and evaluation of a beta-glucan biopolymer formulation of lactoferrin produced using a novel cryomilling technique
Transformation of therapeutic proteins from the new compound stage to a marketed product for clinical use depends on the development of an appropriate formulation, using technologies that avoid the underlying causes of protein degradation. Although synthetic biodegradable polymers have been …
-
Bulk manufacture of complex geometry millirod implants and their degradation and drug delivery characteristics
… (PCL) and curcumin was blended using cryomilling as an alternative to the solvent mixing method. Cryomilling was selected due to its faster processing time and reduced cost of materials in comparison to the solvent method. X-ray diffraction (XRD) was used to characterize the resulting …
-
Additive Manufacturing Materials: Fabrication of Aluminum Matrix Composites
This study aims to validate the ability of cryomilling for the production of high-quality aluminum matrix composite (AMC) powder for powder bed fusion (PBF) additive manufacturing (AM). The spectrum of aluminum-based materials available for AM remains limited due to complex melting and …
-
Processing, microstructure and mechanical behavior of bulk nanostructured Mg alloy
… ductility could be achieved. A combination of cryomilling and spark plasma sintering (SPS) was employed in this project to fabricate a NS magnesium alloy. Nanocrystalline (NC) AZ31 powders were produced by cryomilling. A minimum average grain size of approximately 26 nm was obtained when the …
-
Advanced characterization of the oxidation behavior of grain refined NiAl
… by via sputter deposition, ball milling, and cryomilling was found to vary significantly. Sputter deposition was shown to significantly increase the parabolic steady state oxidation rate constant, while decreasing the length of transient oxidation. Ball milling did not result in an increase in …
-
A novel approach to fabricating interconnected porous PCL-based biodegradable scaffolds for articular cartilage tissue engineering
… The approach consists of three major steps: cryomilling, compression molding, and porogen leaching for the preparation of interconnected porous scaffolds by selective leaching of porogen(s) from blends and composites created by combining cryomilling with conventional compression molding. It …
-
Biodegradable polymer-bioactive ceramic composites for Guided Bone Regeneration
… patients with non-resorbable membranes need. Cryomilling, a solid-state, low-temperature blending process, facilitates bulk fabrication by eliminating difficulties such as high viscosity, insolubility and long processing times. It is a cost-effective technique to generate particles with high …
-
ENHANCING DISPERSION OF CARBON NANOTUBES WITHIN METAL MATRIX COMPOSITES
… including high energy ball milling (HEBM), cryomilling, and wet chemistry methods. The powders were analyzed via scanning electron microscopy (SEM) to determine which method maximizes CNT dispersion while minimizing breakage or agglomerations. It was found that wet chemistry ultrasonication …
-
COLD SPRAYED COATINGS WITH DUAL NANOPARTICLE REINFORCEMENTS FOR WEAR AND CORROSION PROTECTION
… six composites were fabricated through cryomilling and then applied to an aluminum substrate as a cold sprayed coating. Using nano-boron carbide (nB4C) and boron nitride nanoplatelets (BNNP) at various combinations up to 2 vol%, an increase of 11.59% in hardness from the control was …
-
FORMATION OF A PHYSICALLY STABLE AMORPHOUS DRUG COMPLEX
… drug a neutral drug and two basic drugs. Both cryomilling and ball milling of the drug with Neusilin were found to produce the amorphous phase. However the ball milled material exhibited superior physical stability when compared to the cryomilled material at 40 oC/75% RH. 13C SSNMR …
-
Development and analysis of aluminum-PTFE reactive composite material
… Al-PTFE (90-10 wt. %) is prepared through Cryomilling and is shown to be a better method of preparation as compared to room temperature milling. The prepared materials are studied to identify best conditions. The analysis methods include thermal studies both aerobic and anaerobic, Mass …
-
Production of a nanostructured copper by Spark Plasma Sintering
… The nanostructured powder was produced by cryomilling an atomized powder, using a ball-to-powder ratio of 30:1 for 8h; it has a mean grain size of 19±2 nm and shows quite a high thermal stability, as shown by a DSC investigation. The influence of temperature, particle size, pressure on the …
-
Mechanical properties and microstructural characteristics of an Al-Mg alloy with bimodal grain size at room and elevated temperatures
… tension. The material is fabricated through cryomilling, cold isostatic pressing, and extrusion. A full factorial experiment is designed and implemented to test these effects on the material. Post-test examination of the specimens with optical and electron microscopes is conducted in order to …
-
An implantable sustained-release chemotherapy delivery system for the treatment of breast cancer
… PLGA-PTX blend were mixed in a 30:70 mass ratio. Cryomilling was utilized to create the chitosan-PLGA-PTX mixture, due to its proven effectiveness in producing homogenous blends. Implants were then fabricated into rods by injection molding and characterized in terms of content uniformity, …
Page 1 of 2