Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 32 for “"Current spreading"”.
-
Simulation of three dimensional current spreading in photonic crystal VCSEL structures
… simulation technique for calculating the current distribution in a Vertical Cavity Surface Emitting Laser (VCSEL) is proposed and implemented. The technique consists of a hybrid 1D/3D approach to the problem. The 3D aspect of simulation is essential for devices like a photonic crystal …
-
Submicron Scaling in Indium Phosphide/indium Gallium Arsenide Single Heterojunction Bipolar Transistors
… was developed to quantitatively describe the current spreading phenomenon in submicron InP HBTs for the first time. These results suggest that additional device scaling along with improvements in epitaxial materials should lead to further progress in the development of high-speed, low power …
-
Design of III-N vertical-cavity surface-emitting lasers by numerical simulation
… been identified such as resistive lateral hole current spreading layers with high optical loss, low reflectivity bottom distributed Bragg reflectors (DBRs), high thermal resistance, and electron leakage. Mitigation strategies for the abovementioned critical problems will be discussed in detail. …
-
Design, fabrication and characterisation of ultraviolet light-emitting diodes for biomedical applications
… by improving the internal quantum efficiency and current spreading. Furthermore, by introducing interdigitated contacts and a reduced mesa size, fabricated µLEDs demonstrated increased efficiency through enhanced current spreading. The first demonstration of a boron-containing UV LED was also …
-
LOW TEMPERATURE GROWN GAAS AND ITS APPLICATION ON LASER DIODES
… effectiveness of LT GaAs and LT Al0.3Ga0.7As as current confinement layers for laser diode structures were simulated by a commercial software, MEDICI. The simulation results showed that both the LT GaAs and the LT Al0.3Ga0.7As epilayers were effective in confining the current spreading. In …
-
Modeling and Analysis of GaN/InGaN Light Emitting Diodes
… been analyzed with the use of band diagrams, current distribution, radiative recombination rate and IV plots.;Different layers of the device have been studied and analyzed and certain design changes to achieve an enhancement in the efficiencies are proposed. The problem of current crowding in …
-
Contact-Informed Thermal-Electric Modelling of Parallel Gap Resistance Welding for Microwire-to-Pad Joining
… deformation to electrical contact resistance, current redistribution, Joule heating and weld response. The modelling approach combines nonlinear contact mechanics, Holm-based constriction resistance, electric and thermal contact conductance assignment, and transient thermal-electric analysis. …
-
Polarization Engineering for Deep-Ultraviolet Light-Emitting Diodes
… such as top-down nanowire arrays, sphere current spreading LEDs, AlGaN substrate and microsphere arrays, are also developed to further improve device efficiency.
-
OPTICAL BISTABILITY IN INTERDIGITATED SEMICONDUCTOR LASERS
… semiconductor laser based on inhomogeneous current injection. The main characteristics of saturable absorber is bistability in the light versus current curve. This research project examines in detail the effects of saturable absorber using a new device structure developed in this centre. The …
-
Investigation Of Metal Modulated Epitaxy Grown III-Nitride High-Power Electronic And Optoelectronic Devices
… devices. Novel fabrication methods and current spreading layers are introduced in these devices. Furthermore, for the first time in more than 8 decades of AlN research, substantial bulk conduction, both p-type and n-type, was achieved in MME AlN and the first known p-n junction AlN …
-
Tapered cavity surface emitting distributed Bragg reflector lasers
… parameters affecting device performance such as current spreading, carrier diffusion, nonlinear gain-carrier relation, gain saturation, carrier induced antiguiding and thermal lensing. The simulation results are presented and effects of design parameters on device performance are discussed. …
-
Novel micro-pixelated III-nitride light emitting diodes : fabrication, efficiency studies and applications
… that the smaller micro-LEDs have more uniform current spreading, which causes their higher efficiency and higher thermal saturation current density. In addition, the temperature-dependent efficiency droop study shows that both the radiative and Auger recombination coefficients decrease with …
-
Design, Fabrication, and Characterization of Pseudomorphic and Quasi-Pseudomorphic AlGaN Based Deep Ultraviolet Light Emitting Diodes Over Sapphire
… 280nm has the potential to replace mercury lamps currently used in the systems for water/air purification, germicidal and medical instruments sterilization applications. However, this potential has not yet been fully realized as the output power, quantum efficiency and lifetime of deep UV-LEDs …
-
Effect of nonuniformity in temperature distribution on the performance of a stripe-geometry double-heterostructure laser
… its effect on the radiation pattern, threshold current, and emission spectrum of a gain-guiding stripe-geometry double-heterostructure laser. This model takes into account lateral current spreading, carrier out-diffusion, two dimensional heat diffusion, and the resultant gain and refractive …
-
Graphene as Transparent Conductive Film for GaN-Based Vertical Cavity Surface Emitting Lasers
… film (TCF) to effectively laterally spread the current across the active region. The actual material used so far is ITO wish has problems related to the deposition technique and the constantly increasing price of the material. Graphene, a one atom layer thick (0.35 nm) graphite derivative 2D …
-
Transfer printing of nitride based light emitting diodes
… up to 80 µW (355 mW/cm²) when operated at a current density of 20 A/cm². A relatively poor performance was observed with damage to the current spreading metal due to an alkaline wet etch step, needed during processing to yield suspended membranes. This issue was addressed by reversing the …
-
Integrated Inp Photonic Switches
… is also demonstrated. The degree of lateral current spreading is easily regulated by controlling the zinc depth, allowing optimization of the injected currents. Beam steering over a 21 microns lateral distance with electrical current values as low as 12.5 mA are demonstrated. Using this …
-
Efficiency droop mitigation and quantum efficiency enhancement for nitride Light-Emitting Diodes
… > 10%. However, there are still challenges for current state-of-the art InGaN-based LEDs, including ‘efficiency droop’ issues that cause output power quenching at high current injection levels (> 100 A/cm2). In this dissertation, approaches were investigated to address the major issues related …
-
Development of wide-band gap InGaN solar cells for high-efficiency photovoltaics
… including interdigitated grid contact and current spreading contacts are developed to yield low-resistance Ohmic contacts for InGaN solar cells. Preliminary solar cells are developed using a standard design to optimize the InGaN material, where the band gap of InGaN is progressively …
-
Fabrication and transfer assembly of microscale, solid-state light emitting diodes and solar cells for transparent and flexible electronics applications
… that promote improvements in areas of electrical current spreading, light absorption and extraction, and thermal management. To this end, my research has focused on routes to fabricating and assembling solid-state light-emitting diodes and solar cells of indium gallium nitride and …
Page 1 of 2