Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 25 for “"DYNA3D"”.
-
DYNA3D Simulations of Low-Speed Impact Response of Laminated Composite Panels
… is simulated without material damage using the DYNA3D finite element analysis code. The DYNA3D code is a nonlinear transient dynamics simulation tool with a contact algorithm for impact. By gaining a more comprehensive understanding of this dynamic impact event, this work is meant to contribute …
-
LS-DYNA3D Modeling and Simulation for Uncontained Engine Debris Impact on Fuselage Skins
… on fuselage skins are simulated using the LS-DYNA3D finite element analysis code. The LS-DYNA3D code is a nonlinear transient dynamic simulation tool with contact algorithms for impact. A finite element analysis is used to simulate the penetration of aluminum plates impacted by titanium …
-
Finite element simulation of chip formation in orthogonal metal cutting using the Langrangian formulation in DYNA3D
<p>http://www.worldcat.org/oclc/42456244</p>
-
Effect of initial imperfections of the response of cylinders to underwater explosion
… Shock Analysis (USA) code combined with VEC/DYNA3D code is used for the analysis of the effect of explosive shock on numerical models. Initial geometric imperfections are introduced in the numerical model using modal imperfections. The resulting numerical model is then subjected to a …
-
Evaluation of finite element analysis techniques applied to a floating offshore wind turbine
… energy and converting it to electricity. The LS-DYNA3D explicit finite element analysis programme is used in performing the evaluation of the analysis and in creating a full scale model typical to the one evaluated. The developed model (case study) is a 1.4MW power rated floating 3 blades turbine …
-
School bus crashworthiness
… IDEADYN was used as a translator to write a LS-DYNA3D input file. Full frontal and offset frontal impacts were simulated in LS-DYNA3D with an initial velocity of 56 km/hr against a rigid wall. Since hourglassing energy was high in the previous results, a higher order integration was done for all …
-
Numerical modeling of air blast effects on hybrid structures
… concrete is presented. This model, used in LS-DYNA3D, incorporates tensile damage, which allows the concrete to degrade as it is loaded. The concrete model is tested using existing unreinforced and reinforced concrete beam tests. Some beams were plain, others were externally reinforced with …
-
Development and simulation of energy-absorbing guardrail terminal
… vehicle. A nonlinear finite element code, LS-DYNA3D, was used to simulate the cutting phenomenon. The model consisted of fully integrated solid elements in conjunction with an elastic-plastic material model with strain based failure. A very fine mesh with multiple elements through the …
-
Impact analysis of a biomechanical model of the human thorax
… of a three-dimensional finite element model in DYNA3D, a finite element analysis program. The model was validated by comparing the results of tests of body armor systems conducted on cadavers to results obtained from finite element analysis. A parametric study was undertaken to determine the …
-
Crashworthiness of Side Impact Beams
… Ansys v5.4 was used for the static FEA while LS-Dyna3D v940 was used for the dynamic FEA.;The objectives of the project were to assess and then model the behaviour of the steel and composite side impact beams. This behaviour is in terms of both the beams' static and impact response. The beams …
-
Effect Of Childhood Obesity On Risk Of Pelvic Bone Fracture In Simulated Sideways Fall
… explicit dynamic finite element code, LS-DYNA3D (LSTC, Livermore, CA) was used for model simulations. The simulation results indicate that the momentum effect of increased body mass of obese children would be more dominant over the cushion effect of the SAT layer.
-
Computational model of ductile erosion by single particle impact
… was developed in LS-INGRID and analyzed using LS-DYNA3D. The Aluminum metal model was used to simulate the experimental work of Sheldon. The results of the model were checked with experimental results of Sheldon and a close comparison was observed. Several parameters such as velocity of erodent, …
-
Dynamic response of the human skull-brain complex to impact: Points of maximum stress and pressure.
… The analysis is performed using the program LS-DYNA3D for the analysis of frontal, lateral and top impact. The results produced include the loci of points that carry the maximum stresses as the brain mass moves. Various paths result for the different type of stresses (principal stresses, shear …
-
Particle breakage in sand blasting due to impact on ductile materials
… a transient dynamic analysis is performed in LS-DYNA3D. This study focuses mainly on the propagation of stress waves and the volume loss of the sand particle upon impacting an aluminum plate. Three different shapes of the sand particle and five different sizes with varying impact angles and …
-
Failure mechanisms in impact erosion of ductile materials
… and dynamic analysis performed using LS-DYNA3D to predict the erosion loss. Using suitable failure criteria the amount of material lost was predicted. For this purpose, a program written using AWK language was used to find the number of failed elements. The results of this model were …
-
Finite Element Analysis of Ship Collisions
… using the explicit non-linear FE code LS-DYNA3D. Various modeling alternatives are considered. The ability to model a complete ship-to-ship collision is developed incrementally starting with bow collisions with a rigid wall. A super-element (intersection model) approach is considered to …
-
Computational models of particle size effects on brittle oxide scale erosion
… were developed using IDEAS and analyzed using LS-DYNA3D. The aluminum oxide model was used to validate the computational model with the experimental work of Allan Levy. The results indicated the correlation with the experimental observations. The same procedure is extended to estimate the material …
-
Taylor Impact Test and Penetration of Reinforced Concrete Targets by Cylindrical Composite Rods
We use the three-dimensional finite element code DYNA3D to analyze two problems: (a) the normal impact of a cylindrical monolithic or composite rod against a smooth flat rigid target, (commonly known as the Taylor impact test), and (b) the penetration of composite and monolithic steel cylindrical …
-
Enhancement of crashworthiness in car-truck collisions using damped under-ride guard and composite crush elements
… of the car structure is further developed using DYNA3D and an elastic-plastic analysis of the car-to-under-ride guard is performed. The results obtained using the rigid body, lumped parameter model and the finite element analysis are discussed to illustrate the relative merits of the methods. The …
-
A physically-based continuum damage mechanics model for numerical prediction of damage growth in laminated composite plates
… model. The model has been implemented in the LS-DYNA3D commercial finite element hydrocode and the results of the application of the model are shown to be physically meaningful and accurate. Furthermore it is demonstrated that the material characterization parameters can be extracted from the …
Page 1 of 2