Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 233 for “"Design provisions"”.
-
Design provisions for slender concrete columns
… of this study was to evaluate methods of designing uniaxially loaded slender reinforced concrete columns in braced frames.</p> <p>An analytical method was used to predict capacities of a broad range of slender concrete columns. The method incorporates the nonlinear behaviour of concrete …
-
Design provisions for autoclaved aerated concrete (AAC) structural systems
… of this research program was to develop reliable design provisions for AAC structural systems. Typical AAC construction uses AAC shear walls combined with AAC floor or roof diaphragms. AAC shear walls are the predominant structural application of AAC. Because the behavior of AAC shear walls under …
-
Design provisions for autoclaved aerated concrete (AAC) infilled steel moment frames
In this dissertation, the seismic behavior and design of AAC-infilled steel moment frames are investigated systematically. The fundamental vehicle for this investigation is the ATC-63 methodology, which is intended for the establishment of seismic design factors for structural systems. The ATC-63 …
-
Enhancing Building Resistance to Differential Settlement with Canadian Seismic Design Provisions
… on evaluating the influence of Canadian seismic design provisions on the resistance of reinforced concrete buildings against the differential settlement of their foundation. Three types of moment-resisting frame buildings located Vancouver, Montreal and Toronto are designed in accordance with the …
-
Assessment of seismic design provisions for multi-tiered ordinary concentrically braced frames
… seismic performance of the frames. The seismic design provisions for multi-tiered ordinary concentrically braced frames (MT-OCBFs) are assessed in this study. MT-OCBFs are intended to achieve modest levels of ductility, and a relatively simple design procedure is used for them. The current …
-
Strut-and-tie modeling of reinforced concrete deep beams : experiments and design provisions
… with discrepancies that exist between design provisions for strut and tie modeling (STM), were the impetus for the funding of the current project. The overall objective of the project was to develop safe and consistent design guidelines in regard to both the strength and serviceability …
-
Evaluation of the shear design provisions of ACI 523.4R for autoclaved aerated concrete members
… the test program are used to evaluate the shear design provisions of ACI 523.4R “Guide for Design and Construction with AAC Panels”.
-
TOWARDS THE RECONCILIATION OF THE EMPIRICAL AND RATIONAL DESIGN PROVISIONS OF CSA S304-14
Masonry structures in Canada are designed in accordance with CSA S304-14 which includes both empirical and rational design provisions. The two design methods result in inconsistent outcomes in certain cases. This thesis investigates one such case where the empirical design provisions for …
-
Post-earthquake recovery performance of modern buildings and development of recovery-based seismic design provisions
… to develop new recovery-based seismic design provisions that ensure building recovery performance meets societal expectations. In the first half of this dissertation, methods to evaluate functional recovery risk across a broad range of intensity levels are introduced. These methods are …
-
Wind Loads On Non-Rectangular Flat-Roof Buildings: Design Provisions And Application Of Machine Learning
… wind engineering field. Consequently, the wind design provisions of rectangular buildings are well established in the wind codes and standards. On the other hand, wind design provisions for non-rectangular buildings are generally not available in wind codes and standards. This study investigates …
-
Investigation of spacing limits for crack control reinforcement within AASHTO LRFD strut-and-tie modeling design provisions
… crack control reinforcement in the current STM provisions in the AASHTO LRFD specifications limits the maximum spacing to the smaller of d/4 and 12.0 in., and the desired relaxation is to d/2 or 24 in. This was accomplished through a large-scale shear testing of three deep beams with two tests …
-
Experimental and numerical investigations of ductile slender reinforced masonry shear walls subjected to in-plane seismic loads
… (hu/Lw) ratios greater than 1.5, that are designed and detailed with modern seismic design provisions are often used as the seismic-force-resisting system (SFRS) for contemporary buildings. The in-plane seismic performance of these walls is however relatively poorly understood compared to …
-
Evaluation and Calibration of Pedestrian Bridge Standards for Vibration Serviceability
… and emphasis on architecturally appealing designs has resulted in lively pedestrian bridges. A prominent example for this is the serviceability failure of the London Millenium Bridge in 2001, where excessive vibrations from inauguration crowds resulted in shutting down the structure. While …
-
Anchorage of grouted vertical duct connections for precast bent caps
… element to serve as sleeves to house connectors. Designers and contractors prefer this type of precast connection over other types because the volume of grout that is required to complete the capto-column connection is minimized. This research intends to reduce some of the uncertainties that …
-
Πειραματική μελέτη για την συμπεριφορά και τον σχεδιασμό πλαισίων Ο/Σ ενισχυμένων με εμφατνούμενα τοιχώματα Ο/Σ υπό ανακυκλιζόμενη οριζόντια φόρτιση
… in a non-ductile three-story typical RC building designed according to the Greek codes in force prior to 1985. Because of the lack of design provisions regarding specifically the design of R/C infilled frames, as compared with masonry infilled frames for which extensive research has been …
-
Experimental database, analysis and design of noncompact and slender concrete-filled steel tube (CFT) members
… slenderness ratio. AISC 360-10 specifies the provisions for designing noncompact and slender rectangular and circular CFT members under axial compression, flexure, and combined axial and flexural loading. This research presents the development and evaluation of these design provisions. …
-
Toward practical modeling of reinforced concrete flat plate structures
Most reinforced concrete (RC) design provisions have been developed on the basis of experimental data involving isolated and highly-idealized structural elements. As a result, many of the RC-related design provisions currently used are unsuitable for providing accurate assessments of RC structural …
-
Design for shear in reinforced concrete using strut-and-tie and sectional models
The design of reinforced concrete members for shear was studied. Both strut-and-tie models (STM) and sectional methods were examined. Initially, the response of isolated struts was observed. Various layout of reinforcement were used within the isolated struts. Three series of deep beam tests were …
Page 1 of 12