Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 98 for “"Dimples"”.
-
Heat Transfer Augmentation Surfaces Using Modified Dimples/Protrusions
… heat augmentation surfaces roughened by modified dimples/protrusions. The dissertation is composed of two main parts: Part I (Chapters 2-4) for compact heat exchangers and Part II (Chapter 5) for internal cooling of rotating turbine blades. Part I consists of three phases: Phase I (Chapter 2) …
-
Thermal and Hydraulic Characterization of Hook-Shaped Fins and Dimples
… drop of GRIPMetal arrays – hook-shaped fins with dimples – under varying tip clearances and attack angles. Experiments with water-cooled GRIPMetal surfaces explored Reynolds numbers (Re) from 600 to 12,000, while simulations examined attack angles (α) from 0° to 90°. Results showed that GRIPMetal …
-
THERMO-AERODYNAMIC PERFORMANCE OF TURBULENT FLOW OVER DIMPLES OF DIFFERENT DESIGNS
… used to simulate the turbulent channel flow over dimples to investigate the effect of design parameters variation on the thermo-aerodynamic performance. The work focused on three main points as follows: (1) Effect of dimple geometry (shape): In this study, the drag and heat transfer performance …
-
Computational study of laminar flow heat transfer enhancement by dimples and protrusions
… is needed. It appears that protrusion and dimples may sufficiently increase heat transfer rates without a large pressure drop penalty. A comprehensive numerical study was undertaken of the flow and thermal fields along with the heat transfer distribution in the vicinity of isolated, height …
-
Small Laser-Textured Dimples for Improved Tribological Performance of CoCrMo in Artificial Hip Joints
… tribological performance by introducing micro-dimples that enhance lubricant retention and reduce asperity contact. While previous research has largely focused on large dimples, small dimples (~5 µm) remain underexplored despite their potential advantages, including higher coverage, improved …
-
Heat Transfer Augmentation In A Narrow Rectangular Duct With Dimples Applied To A Single Wall
… duct (AR=2) characterized by the application of dimples to the bottom wall of the channel. Experimental testing and numerical modeling is performed for full support and validation of presented findings. The geometries are studied at channel Reynolds numbers of 20000, 30000, and 40000. The purpose …
-
Photochemical Fabrication and Tribological Evaluation of Hexagonal Grooves with Corner Dimples on Cast Iron Surfaces
… hexagonal grooves with corner dimples—on gray cast iron. The resulting textures exhibit uniform groove widths (~13 μm) and varied depths, demonstrating PCM’s capability to create high-resolution patterns with sub-micron precision on industrially relevant substrates. To assess …
-
Experimental Investigation of Dimples as a Heat Transfer Enhancement Feature in Narrow Diverging and Converging Channels
… enhancement feature considered for this study is dimples (inline and staggered) on the main heat transfer surfaces. All the measurements are presented at Reynolds numbers of 3500, 8900, 18000, and 7000, 14000, 28000 for converging and diverging channels respectively. Pressure drop measurements for …
-
Utilization of exterior surface dimples for stream-wise force reduction for a circular cylinder in cross-flow
<p>Applying dimples on spherical bluff bodies have been found to be a major technique to control the surface flow and reduce the stream-wise force. However, not much work has been done on dimple applications on cylindrical Objects .</p> <p>This research project aims to investigate, firstly, whether …
-
Detailed Study of Flow and Surface Heat Transfer Enhancement Mechanism in the Presence of Dimples and/or Protrusions
… auxetic structures) by making spherical inline dimples on both sides of an elastic sheet. Manufacturing technologies such as 3-D printing and additive manufacturing paved the way to realize the complex shapes needed to achieve NPR behavior. These materials are desirable in many engineering …
-
COMPUTATIONAL MODELING OF FLOW CHARACTERISTICS AND ASSESSMENT OF DRAG AND HEAT TRANSFER OF DIMPLED SURFACES
… with studies focusing on passive methods such as dimples, riblets, pin-fins and protrusions. Among these, dimpled surfaces are attractive due to its enhancement in heat transfer performance while requiring less additional power to drive the flow. The interest of optimizing the drag and heat …
-
Enhancing Tribological Properties of Metallic Sliding Surfaces through Micro Multi-texturing Techniques
… A flat end mill was used to generate asymmetric dimples. A different series of symmetric dimpled surfaces were also machined using a single crystal diamond cutter. Cutting forces were modelled and compared with the experimental results. On the symmetric dimpled surface, a multi-scale texture …
-
Surface-Texture Fabrication of Zirconia-Toughened Alumina Using Focused Ion-Beam Machining
… feasibility in the manufacturing of microscopic dimples in zirconia-toughened alumina (ZTA), a wear resistant ceramic used in artificial joint replacements. The interaction between the ion-beam and the ceramic was characterized in terms of material removal rate (MRR), surface roughness, and …
-
Mitigation of Aeroacoustic Noise of a Fixed Wing Using Passive Flow Control
… is of increasing concern. In this study, shallow dimples are applied to a NACA 0012 airfoil at multiple angles of attack (AoA) with the intent of reducing aeroacoustic noise emissions. Both Reynolds Averaged Navier-Stokes (RANS) and Large Eddy Simulation (LES) models are used for aerodynamic and …
-
Detailed Experimental Measurements of Heat Transfer Augmentation in Internal Channels Using a Thermochromic Liquid Crystal Technique
… viz. dimple and swirl induced jet impingement. Dimples are suitable candidates for high performance enhancement as they impose a low pressure drop penalty. The present study aims at experimentally measuring heat transfer on all the walls of diamond, triangular, square and cylindrical shaped …
-
Detecting dimple defects of polished semiconductor wafer surfaces
… an automated visual inspection system to detect dimples of polished wafers. Dimples are common defects on polished wafers. They appear as circular-shaped bright spots which usually vary in sizes and locations. They may also have irregular boundaries and co-exist with other image features. …
-
Design and Validation of a Force Measurement System for the Analysis of Airfoil Lift and Drag Characteristics
… from the design of a golf ball, as the dimples are known to delay flow separation which allows the ball to travel further. In relation to wing design, there has been very little research available that either proved or dismissed the theory of using a roughened airfoil surface to reduce …
-
An investigation into the use of low aspect ratio spherical wells to reduce flow separation on an inverted wing in ground effect
… the ability of low aspect ratio spherical wells (dimples) to produce vortices for flow mixing. Dimpled surfacing on an inverted Tyrrell026 airfoil in ground effect (indicative of high performance automotive aerodynamic applications e.g. Formula One) has been investigated for similar vortex …
-
Tribological studies of surface texturing for application in air-conditioning and refrigeration compressors
… experiments, the beneficial effect of the micro-dimples could be attributed to the lubricant storage ability. A trade-off between the effect of the material pile-ups or bulges around the micro-dimples and the lubricant storage volume of the micro-dimples determined the difference in performance …
-
Modeling and Performance Analysis of Alternative Heat Exchangers for Heavy Vehicles
… rectangular fin, rectangular fin with one-side dimples, and rectangular fin with two-side dimples. The computational fluid dynamics (CFD) approach is applied for the comparative studies by using the ANSYS FLUENT software. Moreover, the simulation results are verified by experimental results from …
Page 1 of 5