Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 23 for “"Drag torque."”.
-
Drag Torque and Synchronization modelling in a Dual Clutch Transmission
… engaging them to each other. However, there is a torque, the gearbox’s drag torque, that can interfere with this process by slowing down the input shaft. This drag torque therefore aids the synchronization process during an up-shift and resists it during a down-shift. Today’s automotive industry …
-
Drag Torque and Synchronization modelling in a Dual Clutch Transmission
… engaging them to each other. However, there is a torque, the gearbox’s drag torque, that can interfere with this process by slowing down the input shaft. This drag torque therefore aids the synchronization process during an up-shift and resists it during a down-shift. Today’s automotive industry …
-
Study of drag torque in a two-speed dual clutch transmission electric vehicle powertrain system
… consider the proposed two-speed transmission drag torque, including its influences and potential applications. The focus of this thesis is on studying the drag torque within two-speed dual clutch transmissions. Different source of drag torque in the DCT are theoretically analysed and modelled, …
-
Measurements of Drag Torque and Lift Off Speed and Identification of Stiffness and Damping in a Metal Mesh Foil Bearing
… presents the measurements of MMFB break-away torque, rotor lift off and touchdown speeds, temperature at increasing static load conditions, and identified stiffness and equivalent viscous damping coefficients. The experiments, conducted in a test rig driven by an automotive turbocharger …
-
Evaluation of Coated Top Foil Bearings: Drag Friction Coefficient, Operating Drag Torque and Lift-Off Speed, and Dynamic Force Coefficients
… at room temperature (21°C). The dry-sliding torque (T), recorded with a precision meter, increases linearly with an increase in applied static load (max W/(LD)=25.6 kPa). The bearing with a VN coated top foil shows the largest turning torque. The dry-sliding friction factor f =T/(1/2 WD) …
-
Measurement of Drag Torque, Lift Off Speed, and Identification of Frequency Dependent Stiffness and Damping Coefficients of a Shimmed Bump-Type Foil Bearing
… μm and 50 μm). Parameters of interest include drag torque, rotor lift off speed, and the estimation of force coefficients of a BFB with shims (30 μm and 50 μm thick). The thesis also compares those results to those of the original BFB (without shims). Drag torque measurements during shaft …
-
Modeling and Simulation of Multiphase Flow between Rotating and Stationary Disks
… from the engine to the wheels with the speed and torque controlled by a gearbox. To accommodate different speeds and loads, different gear ratios are needed, and the clutch disengages and engages every time those ratios are changed. Since heat is generated when disengaged and when suddenly …
-
Μοντελοποίηση, σχεδιασμός και βελτιστοποίηση πολύδισκων συμπλεκτών υγρής τριβής
… phenomena and the aim is to decrease drag torque. The capturing of the two-phase air-oil flow characteristics plays a major role in that scope. Two-phase flow occurs in certain operating conditions where the suction of air from the outer radius is permitted leading to the decrease of …
-
Finite Element Simulation of Energy Loss in Friction Brakes
… to energy loss in a vehicle is crucial. Brake drag is one such mechanism, and it is estimated to account for around 3% of energy loss in a vehicle. Improving the energy efficiency of friction brakes can help address range anxiety and improve the overall performance of electric vehicles. Virtual …
-
Directed energy effects on the flight path of a spinning ballistic projectile
… instability or range reduction. Skin friction drag may be increased from surface roughness generated by a pulsed energy source. The results that this thesis will examine include: impulse generated by the laser interaction, additional Magnus effects and aerodynamic drag. Moment induced …
-
THE ROTATIONAL DYNAMICS OF ATMOSPHERIC ICE: ELECTRICAL AND AERODYNAMIC TORQUES
… times. At low Reynolds numbers, the electrical torque is opposed by a Stokes drag torque. The resulting equation of motion is that of a damped pendulum oscillator. At higher Reynolds numbers, the electrical torque competes with an aerodynamic torque which itself attempts to produce an alignment …
-
DEVELOPMENT OF A STOP & START SAILING STRATEGY FOR NEXT GENERATION POWERTRAINS
… at minimal cost. S&S system removes the engine’s drag torque, when no traction is required, preventing from burning extra fuel. According to upcoming homologation cycles and due to more stringent CAFE (Corporate Average Fuel Economy) targets, S&S should be further improved, by operating it even …
-
Hybrid air foil bearing with external pressurization
… wear during start-up/shut down, and also reduces drag torque during starts. Furthermore, this hybrid foil bearing does not need cooling system. An experimental test with a loaded bearing under hydrostatic mode demonstrates the high potential of hybrid air foil bearings. The load capacity of the …
-
Experiments and Predictions with a Foil Thrust Bearing Supported by Metal Mesh Screen
… with cases from the literature. However, bearing drag torque measurements and predictions for a six-pad MMFTB do not agree well. A simple Couette-flow approximation for the bearing drag torque shows that the bearing would need to operate with a uniform film thickness (hconst = 2.7 μm) to produce …
-
A Thermo-Elasto-Hydrodynamic (TEHD) Computational Analysis for the Force Performance of Self-Equalizing Tilting Pad Thrust Bearings
… above the nominal rate, increases the bearing drag torque but has little effect on the pad peak temperature rise or the pad minimum film thickness. A reduced flow, below the nominal rate, produces areas denuded of oil at both the pad leading edge and trailing edge, and thus the pad minimum film …
-
Measurements of leakage, power loss and rotordynamic force coefficients in a hybrid brush seal
… thin EDM-webs to the seal casing. The measured drag power at low rotor speeds (< 11 m/s at 1,300 rpm) decreases as the pressure differential across the seal increases. At a fixed rotor speed, a significant drop in drag torque (and drag power) ensues as the supply pressure increases, thus …
-
High Temperature Leakage Performance of a Hybrid Brush Seal Compared to a Standard Brush Seal and a Labyrinth Seal
… at high supply pressures. Measurements of the drag torque of the test seals show the HBS has a larger torque when pressurized compared to the brush seal and labyrinth seal. This indicates that the HBS experiences a larger degree of blow-down due to the pads decreasing the clearance. The …
-
Modelling, simulation and implementation of a fault tolerant permanent magnet AC motor drive with redundancy.
… mathematical model to produce the desired output torque was developed to minimize copper loss and torque ripple in the motor drive, which is applicable to both sinusoidal and trapezoidal brushless permanent magnet motor types. A detailed fault effect investigation was performed in this thesis and …
-
Development of a Clutch Assisted Engine Start
… the engine o at idle to remove engineâs drag torque could be adopted at vehicle in motion, extending the distance covered by the vehicle coasting, when no traction is required, by opening the clutch automatically. Literature calls such operation âsailingâ: represents a low cost control …
-
7DCT Transmission efficiency optimization: Design and simulation of oil traps that reduce the churning los
… an improvement of the gearbox that lower the torque that is required to rotate it. To verify the results a prototype is built with materials available in the company’s workshop and investigated if it can withstand a test in a testing rig. With the use of CFD-analysis (Computational Fluid …
Page 1 of 2