Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 84 for “"Dry sliding"”.

  1. Wear modelling and FEA simulation for dry sliding contacts

    … nodal pressures at the contact region for small sliding steps. These pressures are then inputted to a customised wear calculating routine. The routine uses averaged wear coefficients (wear rates) obtained from custom designed experiments. The FEA contact geometry is modified after each sliding …

    adelaide Repository record for Wear modelling and FEA simulation for dry sliding contacts (opens in a new tab)

  2. Scuffing of Aluminum/steel Contacts Under Dry Sliding Conditions

    Based on the experimental observations and the scuffing models a new hypothesis for scuffing is proposed. According to this hypothesis, scuffing involves initiation of cracks due to subsurface plastic deformation, propagation of these cracks leading to the removal of the existing protective surface …

    uiuc Repository record for Scuffing of Aluminum/steel Contacts Under Dry Sliding Conditions (opens in a new tab)

  3. Dry sliding wear of metals: From subsurface microstructure to tribological behavior

    Dry sliding wear behavior of Cu-15Ni-8Sn bronze was studied by performing pin-on-disc wear tests against different counterface materials under various loads. The microstructure of the debris, worn surface and subsurface of the bronze were characterized using scanning electron microscopy (SEM), …

    uiuc Repository record for Dry sliding wear of metals: From subsurface microstructure to tribological behavior (opens in a new tab)

  4. Dry Sliding Tribological Characteristics of Hard, Flat Materials with Low Surface Roughness

    … and high modulus of elasticity, suitable for sliding in dry friction conditions under a normal load. A wide range of materials including various steels, various coatings on tool steels deposited by various deposition techniques and different ceramics were examined and considered for …

    usf Repository record for Dry Sliding Tribological Characteristics of Hard, Flat Materials with Low Surface Roughness (opens in a new tab)

  5. Tribology and Surface Engineering for Lubricious Dry-Sliding Contacts of MoS2 Based Coatings

    … the lubricity of MoS2 during room temperature sliding is drastically reduced in humid, terrestrial atmospheres. The reason behind this degradation is not fully understood, with multiple conflicting arguments as to why this may be the case. One leading hypothesis suggests that adsorbed water …

    whiterose Download PDF for Tribology and Surface Engineering for Lubricious Dry-Sliding Contacts of MoS2 Based Coatings (opens in a new tab)

  6. Dry sliding and contact fatigue behavior of different high density Ni-Cu-Mo PM Steels

    … In this research two very common phenomena, dry sliding and contact fatigue behavior of PM parts have been investigated. In the first part of the work dry sliding behavior of Fe-Mo-Cu-C and Fe-Mo-Cu-Ni-C steels were investigated. This study was done to investigate the influence of Ni on dry …

    trento Repository record for Dry sliding and contact fatigue behavior of different high density Ni-Cu-Mo PM Steels (opens in a new tab)

  7. Mechanisms of Formation and Effects of Transition Metal Oxides in Silicon Nitride on Steel Dry Sliding Contacts

    Silicon nitride on steel sliding contacts may provide advantageous tribological properties over traditional self-mated pairs, however the friction and wear behavior at high sliding speeds (>1 m/s) is not well understood. Previous studies at low sliding speeds (< 1 m/s) have found that the wear …

    unt Repository record for Mechanisms of Formation and Effects of Transition Metal Oxides in Silicon Nitride on Steel Dry Sliding Contacts (opens in a new tab)

  8. Design Of Novel High-Performance Materials For Sliding Applications

    … wear performance of PEEK-based composites during dry sliding. Ethanol lubricated composites showed lower wear than dry sliding. Advanced ceramics like SiC and Si3N4 are widely applicable and play a major role in water-based lubricated systems. SiC and Si3N4 showed lower wear rate during ethanol …

    nodak Repository record for Design Of Novel High-Performance Materials For Sliding Applications (opens in a new tab)

  9. The adhesive wear of modern and traditional engineering coatings

    … under conditions of constant load and sliding speed. The wear tests were carried out under dry sliding contact using the standard pin-on-disc wear testing equipment. The engineering coatings investigated were electroless nickel PTFE composite, conventional electroless nickel, hard …

    aston Repository record for The adhesive wear of modern and traditional engineering coatings (opens in a new tab) Download PDF for The adhesive wear of modern and traditional engineering coatings (opens in a new tab)

  10. Energy and Thermodynamically Based Approaches for Analysis of Damage in Contact Problems

    … These include disk-on-disk unidirectional dry sliding, pin-on-flat reciprocating dry sliding and pin-bushing grease-lubricated oscillatory sliding. It is shown that the wear rate is linearly related to the power dissipation as well as the entropy generation rate. The linear correlations are …

    lsu-thes Repository record for Energy and Thermodynamically Based Approaches for Analysis of Damage in Contact Problems (opens in a new tab)

  11. An investigation of friction and wear mechanisms in selected thermoplastics

    … observations of abrasive wear of a polymer disk sliding against metal asperity models. The investigator was unable to observe actual particle formation but did identify elastic and plastic deformation of the polymer, and a debris buildup and extrusion process occurring at the leading edge of the …

    vt Repository record for An investigation of friction and wear mechanisms in selected thermoplastics (opens in a new tab)

  12. Modeling Friction between Metals in Dry Contact Following Run-In

    By extending previous work on sliding friction and contact mechanics, friction between metals in dry sliding contact following run-in is analyzed. A friction model which includes the effects of elastic/plastic deformation along with surface adhesion and entrapped wear debris plowing is proposed. …

    ucf Repository record for Modeling Friction between Metals in Dry Contact Following Run-In (opens in a new tab)

  13. Tribological Performance of Advanced Polymeric Coatings Under Extreme Operating Conditions

    … thin polymeric coatings in environments such as dry sliding bearing, valve sealing surfaces, hydrodynamic bearings and drilling application under different extreme working conditions. Three groups of polymers, namely Polytetrafluoroethylene (PTFE)-based, Polyether ether ketone (PEEK)-based, and …

    tamu Repository record for Tribological Performance of Advanced Polymeric Coatings Under Extreme Operating Conditions (opens in a new tab)

  14. The tribological and wear properties of carbon-graphite composites

    … has been carried out using abrasive wear, dry sliding wear, particle erosion, slurry erosion, cavitation erosion and the corresponding wear rates have been related to the bulk properties of the different materials. In all tests; hardness, elastic modulus, porosity and the presence of …

    cape-town Repository record for The tribological and wear properties of carbon-graphite composites (opens in a new tab)

  15. Evaluation of Coated Top Foil Bearings: Drag Friction Coefficient, Operating Drag Torque and Lift-Off Speed, and Dynamic Force Coefficients

    … bump-type foil bearings (BFBs) have issues of dryfriction during sliding contact at rotor start/stop cycles. To prevent premature wear of both shaft and the BFB, the proper selection and application of a coating on the top foil is of importance to ensure bearing long life. This thesis presents …

    tamu Repository record for Evaluation of Coated Top Foil Bearings: Drag Friction Coefficient, Operating Drag Torque and Lift-Off Speed, and Dynamic Force Coefficients (opens in a new tab)

  16. Infrared radiometric measurements of surface temperatures generated by friction of sliding iron-on-sapphire

    … of surface temperatures produced during dry sliding contact were made by using an advanced infrared microscope which receives radiation from a very small target area e.g., 1.78 x 10⁻⁵m in diameter for a 36X objective, allowing temperature measurements within a general region of contact. …

    vt Repository record for Infrared radiometric measurements of surface temperatures generated by friction of sliding iron-on-sapphire (opens in a new tab)

  17. Investigation of Thermal, Mechanical, and Tribological Behaviour of Biobased-resin-crosslinked, Sisal-fibre-reinforced Epoxy Composites

    … reinforcement agent was studied under dry sliding.The dry-sliding wear resistance property of bio-based cross-linker-cured, sisal fibre reinforced epoxy network was found to be superior, due to enhanced flexibility. The functional groups, nature of curing and degradation of epoxy resin …

    toronto-retro Repository record for Investigation of Thermal, Mechanical, and Tribological Behaviour of Biobased-resin-crosslinked, Sisal-fibre-reinforced Epoxy Composites (opens in a new tab)

  18. Tribology of High-Performance Polymers at Extreme Conditions From Cryogenic to Elevated Temperatures

    … oil lubricants and greases, resulting in dry sliding conditions that generally have significant detrimental effects on component performance; with the addition of abrasive dusty environment in Mars, the complexity is further compounded. To address these challenges, high-performance …

    tamu Repository record for Tribology of High-Performance Polymers at Extreme Conditions From Cryogenic to Elevated Temperatures (opens in a new tab)

Page 1 of 5