Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 14 of 14 for “"Dry spots"”.
-
Investigations on statistical analysis of turfgrass rating data, localized dry spots of greens, and nitrogen application techniques for turf
Thesis (Ph. D.)--Michigan State University. Department of Crop and Soil Sciences, 2000
-
Contributions to the study of the capillarity of thin liquid films: analysis of measurements of dry spot nucleation and the use of diffuse interface theory for contact line dynamics
… substrate tends to destabilize the film forming dry spots. The surface tension retards this by stretching the surface of the liquid. Viscosity also determines the dynamical time scale for the nucleation (formation) of dry spots. Our work is part of an ongoing research at the MTP group of the TUE. …
-
Fluid dynamics of non-Newtonian thin films: squeezing flow, film rupture, and contact line instability
… the rupture process which could create dry spots earlier than Newtonian fluids. Dry spots are usually unwanted for both functional and aesthetic purposes. Numerical models of contact line instability have shown that the shear-thinning rheology increases the finger growth rate for …
-
Characterizing the Effects of Capillary Flow During Liquid Composite Molding
… fibers is a major quality issue as it results in dry spots or voids. Void formation occurs at the resin flow front due to competition between viscous forces and capillary pressure. The purpose of this work is to characterize capillary pressure in vacuum infusion, and develop a model that can be …
-
Remediation of Soil Hydrophobicity on a Coastal USGA Sand-Based Golf Green
Managing soil hydrophobicity caused by localized dry spots (LDS) on sand based golf greens has become one of the greatest challenges for golf course superintendents and managers, especially as water restrictions intensify. The purpose of this study was to evaluate the effectiveness of thirteen soil …
-
Enhancement of properties of carbon-fiber-reinforced TGDDM/DDS epoxy composites containing nanoclay
… had uniform fiber volume fraction, fewer dry spots, and fewer resin-rich areas. The plain-strain fracture toughness of nanoclay-filled epoxy composite was measured by single-edge-notch bending testing. The testing results indicated that both the critical-stress-intensity and the critical …
-
An investigation of defect evolution in foam core sandwich structures produced using vacuum assisted resin transfer moulding
… were effective at detecting defects such as dry spots and incomplete resin infiltration. However, due to technical limitations of these methods visual inspection of high quality digital images proved to be the most accurate method for evaluating the specimens. The effect of these defects was …
-
Processing of MW-Scale Wind Turbine Rotor Blades by Vacuum-Assisted Resin Infusion Molding
… costly manufacturing defects, such as unwetted dry spots, in the large composite structure. In this research, two laboratory-scale WTB shell section preforms were infused with resin in a VARIM process. The purpose of the first experiment was to observe the temperature change within the preform …
-
Field and Laboratory Studies on the Development and Control of Soil Water Repellency of Sand Root Zone Mixes
Localized dry spots (LDS) associated with water repellent (i.e., hydrophobic) soils have detrimental effects on the survival, playability, and aesthetic value of creeping bentgrass (Agrostis palustris) used for golf course putting greens. The development of water-repellent soils, using molarity of …
-
Degradation of toluene and trichloroethylene in a radial flow reactor
… distribution of the feed helped to prevent dry spots and channeling in the bed. Mass transfer rate was determined to be fast relative to the reaction rate for toluene. Between 0 and 30 mg toluene/L in a batch culture, initial toluene degradation rate was a linear function of specific …
-
Experimental investigation of regular fluids and nanofluids during flow boiling in a single microchannel at different heat fluxes and mass fluxes
… critical heat flux occurs and create channel dryout. Dryout causes high surface temperatures that can destroy the electronic circuits that use two-phase micro heat exchangers for cooling. Flow boiling instability is characterized by periodic oscillation of flow regimes which induce …
-
Analysis of dry spot formation in RTM through optimization of non-Newtonian resin parameters
Resin Transfer Molding, or RTM, is one of the most popular methods in today’s world for manufacturing composite materials. The capacity for creating flexible and complex geometries of high volume fraction at lower costs makes it a very appealing manufacturing process for both the automotive and …
-
THE RESPONSE OF BERMUDAGRASSES [Cynodon dactylon (L.) Pers. x C. transvaalensis Burtt-Davy] AND CREEPING BENTGRASS [Agrostis Stoloniferi (L.)] TO A COMMERCIAL HUMECTANT AND WETTING AGENTS DURING SUMMER
… and various wetting agents on localized dry spots (LDS) on a `TifEagle' bermudagrass putting green; (v) evaluate a humectant and various wetting agents on non-irrigated common and `Tifway' bermudagrass blend in a sports field; (vi) assess the changes in volumetric water content (VWC) of a …
-
Effects of surfactant-based wetting agents on cereal growth and physiology
… soil water repellency and alleviate localised dry spots. More recently, applying surfactants to soil has been considered as an alternative way of enhancing nutrient and water use efficiencies of arable crops. However, the mechanisms by which surfactants affect plant physiological responses to …