Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 27 for “"Duroid"”.
-
Development of lightweight and low-cost microwave components for remote-sensing applications
… dielectric properties of organic substrates RT/duroid 5880, 6002 and 6202 are presented from 30 GHz to 70 GHz, covering most of the Ka and V radar bands, giving also a thorough insight on the uncertainty of the microstrip ring resonator method by means of the Monte Carlo uncertainty analysis. …
-
Design of Reconfigurable Annular Slot Antenna (ASA) for Wireless Communications / WLAN Applications
… Slot Antenna (ASA). The antenna is fabricated on Duroid with dielectric constant 6.15. The ASA operates in three different frequencies: 5.2, 5.8 and 6.4 GHz. The matching at those frequencies is achieved using linear stubs. PIN diodes are used as switches to connect/disconnect the stubs to the …
-
Linearly tapered slot antenna
… for an antenna operating at 10 Ghz. LTSA on a Duroid substrate fed by a stripline has been designed to operate with better than 12 dB return loss. Fabricated antenna was characterized and had even a wider response than the CAD design. Radiation patterns also were measured for this antenna. …
-
Nízkošumový zesilovač pro pásmo S
… line filtrem. První je navržen na substrátu Duroid 5880 s relativní permitivitou 2,2 a tg d = 0,009. Pro realizaci byl použit materiál FR-4 (r = 4.34) s tloušťkou 0.06”.
-
Antenna Multi-Band Enhancement by Employing Negative Impedance Converters
… The boards were fabricated on Rogers RT/duroid 5880, laser machined using a picosecond laser and subsequently tested for its scattering parameters. Performance measurements at both, without DC bias and 10 V, revealed a notable difference in matching between the active and passive states, …
-
Design and realization of a 24 GHz receiver front-end in integrated quasi-planar technique.
… have been realized on 10 mils thick RT-Duroid 5880 (dielectric constant $\in\sb{\rm r}$ = 2.22) suspended in the E-plane of a WR-42 waveguide. The receiver incorporates a 24.0 GHz oscillator (LO) and accepts an input radio frequency signal (RF) at 24.4 GHz with a bandwidth of 500 MHz. …
-
Multilayer antenna arrays for environmental sensing applications
… such as Liquid Crystal Polymer (LCP) and RT/Duroid®, provides a lightweight and low cost 3D solution for the fabrication of the antenna arrays. The elements of the antenna arrays are rectangular patches. Two feeding mechanisms, aperture coupling and via feed, were implemented and compared. …
-
Desenvolvimento de um ressoador retangular de fenda com múltiplas camadas de substrato e com utilização de material PBG para sistema de comunicação sem fio
… S to X. Was used as the dielectric material RT/Duroid 5870 and RT/Duroid 6010.LM where both are laminated ceramic-filled PTFE dielectric constants 2.33 and 10.2, respectively. Through an experimental investigation was conducted an analysis of the simulated versus measured by observing the …
-
IEEE 802.11b Wireless LAN Sensor System and Antenna Design
… mm x 4.75 mm has been realized using Rogers 5880 duroid (permittivity = 2.20 ; loss tangent = 0.0004) with 4.4 dBi of gain, > 80 MHz, and a return loss > -32 dB. These types of performance characteristics make the antenna highly desirable for both 802.11b and Bluetooth applications.
-
Aperture Coupled Microstrip Antenna Design and Analysis
… The substrate material is changed from RT Duroid (material in nominal HFSS design) to FR4 due to lower cost and availability. The operating frequency is changed from 2.3GHz (specified in nominal HFSS design) to 2.4GHz for wireless communication applications. Required dimensional adjustments …
-
Ferroelectric microwave circuits
… design of tunable attenuator based on Roger/Duroid 6010LM substrate of dielectric constant 10.2. The application of ferroelectric thin-films enables continuous variation of attenuation under controlled bias voltages with significant size and weight reduction in the overall device.
-
EMI investigation and suppression filter design for wireless robotic control application
… for higher-than-680 MHz models on Rogers RT/duroid® 5880 high-frequency substrates. The S-parameters and phase responses of the BSF prototypes were measured using a network analyzer. The measured results were close to the simulated ones, with an emphasis on selectivity at the cutoff …
-
Optimum configuration of a foreshortened antenna
… made of copper were fabricated on a Rogers RT/Duroid substrate with flange mount SMA connectors for the feed probe. Modeling consisted of changing the shape of the antennas while holding the circuit at a resonance of I GHz. For the antennas analyzed, results show that the highest quality factor …
-
Reconfigurable and micromachined microwave structures
… has been designed, fabricated and tested using DuroidRTM circuit board material from Rogers Corporation. This diplexer exhibits channel bandwidths of less than 3%, and was used as a test structure for subsequent construction on silicon. Using silicon micromachining techniques the diplexer has …
-
Otimização de superfícies seletivas de frequência com elementos pré-fractais utilizando rede neural MLP e algoritmos de busca populacional
… patches on single-layer dielectrics (FR4, RT/duroid). Shapes presented by Sierpinski island and T fractal geometries are exploited to the simple design of efficient band-stop spatial filters with applications in the range of microwaves. Initial results are discussed in terms of the …
-
Integrated Antennas and Active Beamformers Technology for mm-Wave Phased-Array Systems
… The design of patch antennas on the low-cost RT/Duroid substrate and the slot antennas on the IPD technologies as well as the compact on-chip slot DRA antenna are explained in the antenna design section. The design of reflective-type phase shifters in CMOS and MEMS technologies is explained. …
-
Electrically small high-temperature superconducting Y-Ba-Cu-O meander dipole antennas for space-limited applications
… antennas were fabricated from copper (on RT/duroid substrate) whilst the symmetrical meander antennas were fabricated from copper, thick- and thin-film high temperature superconducting (HTS) materials. The first type of meander antennas was fed from underneath the circuit, through the …
-
Tunable Substrate Integrated Waveguide Filters Implemented with PIN Diodes and RF MEMS Switches
… a three-layer PCB is fabricated using Rogers RT/duroid substrates. The first tunable design utilizes the Philips BAP55L PIN diode. This two-pole filter provides six frequency states ranging from 1.55 GHz to 2.0 GHz. Fractional bandwidth ranges from 2.3 percent – 3.0 percent with insertion loss …
-
Broadband dielectric resonator antennas for WLAN applications
… of 0.0035. The substrate material is Rogers RT/Duroid 5880 (TM) with [varepsilon] s =2.2, a loss tangent of 0.0009, and 0.767 mm thickness. The half-cylindrical DRA is used to have the TEo13 mode excited. The radiation patterns of the three antennas are similar to that of a magnetic monopole …
-
Class-F Power Amplifier with Maximized PAE
… efficiency power amplifier is fabricated on RT/duroid 5870 high frequency laminate board. In this design, the harmonics at the input are controlled as well as the harmonics at the output. An input wave-shaping network is designed to shape the waveforms at the gate. In this case, the PAE is …
Page 1 of 2