Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 166 for “"Dynamic measurements"”.
-
Dynamic measurements with a luminescent photoelastic coating
… strain. This research thesis focuses on the dynamic application of the technique, specifically cyclic-load cases as the image intensity is too low for the camera to accurately capture transient-load cases. The dynamic tests involved bar specimens and square-tube specimens loaded at 1 Hz and …
-
Three Dimensional Digital Image Correlation for Dynamic Measurements
… have recently begun to use DIC for full field dynamic analysis. Commercial packages have focused on strain analysis, with few software packages having any modal analysis capabilities built in. Commercial packages are also quite expensive. The goal of this work is to provide an open-source 3D …
-
Planning, performing, and interpreting dynamic measurements in pressurized water reactors
<p>Dynamic tests were performed on the Oconee I nuclear power system at 40, 75, and 95 percent of full power. The tests used pseudorandom binary and multifrequency binary perturbation of reactivity. Recordings were made of the resulting output of plant parameters including neutron power, steam …
-
Dynamic Measurements of the Grüneisen Coefficients of Tantalum, Uranium, and Uranium-Molybdenum Alloys
… c1, and t0. e(x) was determined from calorimeter measurements of the temperature change through the irradiated specimens. It was observed that t0 increased with the atomic number and density of the irradiated specimens. The Grüneisen coefficients of the test specimens were then computed from these …
-
Dynamic Measurements of Lubrication Film Thickness of UHMWPE Contacts for Total Joint Replacements
… knee joint simulator was used while dynamic contact pressure measurements under both dry and lubricated conditions were made using the sensor technology employed in two different artificial knee implant geometries. Each implant was machined by the manufacturer from custom blocks of …
-
A method for systematic interpretation of dynamic measurements in a high temperature gas-cooled reactor
<p>Large linear dynamic models for nuclear reactor systems are widely used for simulation and control system design. It is important to be able to verify these models and the parameters in them. Existing parameter identification techniques are very time-consuming for use with large systems. This …
-
Dynamic Measurements with Scanning Probe Microscopy: Surface Studies Using Nanostructured Test Platforms of Metalloporphyrins, Nanoparticles and Amyloid Fibrils
… with dimensions ranging from 1 to 200 nm. Dynamic MSM-AFM measurements can be obtained by placing the tip on a vibrating nanoparticle and sweeping the frequency or field strength. Changes in frequency spectra and vibrational amplitude can be mapped for nanoparticles of different sizes, …
-
GNSS imtuvo kūrimas ir tyrimas naudojant SDR /
… the experimental part, sensitivity, static and dynamic measurements were performed. The sensitivity measurements showed that USRP B210 is more sensitive than HackRF One by at least 5 dB, because it was still able to detect weaker injected signals. Static and dynamic measurements showed that the …
-
Development and application of luminescent coatings for the measurement of pressure and strain
… techniques in the areas of mechanics and aerodynamics. Two such full-field techniques are PEC and PSP. For PEC measurements, the newer technology of micro-polarizer lens reduces the steps necessary to extract polarization data, hence allowing for faster and dynamic measurements. Similarly, …
-
Static and Rotordynamic Analysis of a Plain Annular (Liquid) Seal in the Laminar Regime with a Swirl Brake for Three Clearances
… mm (0.25 in). The author conducts static and dynamic measurements at = 2, 4, 6, 8 krpm, = 2.07, 4.14, 6.21, 8.27 bar (30, 60, 90, 120 psi), and eccentricity ratios, = 0.00, 0.27, 0.53, and 0.80. Static measurements include leakage rate, pre-swirl ratio and outlet swirl ratio, and the static …
-
A Relation Between Adiabatic and Isothermal Moduli
… sub-surface in exploration areas has also grown. Dynamic elastic properties can be extracted from seismic or well log velocity information; however for geomechanical modeling purposes, it is often desirable to obtain static measurements directly from core samples. Accurate static measurements are …
-
Development of telemetry for the agility flight test of a radio controlled fighter model.
… Air Vehicles provide an excellent platform for dynamic measurements and agility research. A 1/8-scaled F-16A ducted-fan radio-controlled aircraft was instrumented with a telemetry system to acquire angle of attack, sideslip angle, control surface deflection, throttle position, and airspeed data. …
-
Parameter Estimation Using Sensor Fusion And Model Updating
… testing of the structure using static and/or dynamic measurements can be utilized to update the unknown parameters. Optimization programs are used to update the unknown parameters by minimizing the error between the analytical and experimental measurements. Through parameter estimation, …
-
Analysis of fluid-structure interaction under hydrodynamic shock conditions by the finite element method
Electronic Thesis or Dissertation
-
Development of a digital-based particle image velocimetry (PIV) technique
Thesis (M.S.)--Michigan State University. Department of Mechanical Engineering, 1992
-
Fluid diffusion in porous silica
Thesis (Ph. D.)--Michigan State University. Department of Physics and Astronomy, 1998
-
Assessment of Steel Truss Bridges Using Distributed Strain Measurements
… with the added benefit of capturing thousands of measurements with a similar effort required to obtain a single measurement with conventional strain gauges. The current research investigated the use of distributed fibre optic strain measurement to monitor the behaviour of steel truss bridges. A …
-
GA-based substructural identification with static measurements
… systems. To reduce computational time, static measurements are used instead of dynamic measurements. Here, GA works as an optimization tool to identify the unknown stiffness and displacement parameters. The fitness function formulated uses a combination of displacement errors and static …
-
Development of an Optical System for High Precision Multi-Axis Force Measurements
Accurate and precise force measurements are critical in machining operations for maximizing production, detecting tool failure, and monitoring. Currently, the most accurate force sensors are piezoelectric sensors. The accuracy of these sensors is very high, yet they are expensive, are limited in …
Page 1 of 9