Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 22 for “"Dyno"”.
-
Numerical Heat Transfer Simulations of Brake Discs under Dyno-Test Load Cases
Automotive brake discs are critical safety components whose performance heavily relies on efficient thermal dissipation. Yet, conventional laboratory dynamometer testing remains costly and time-consuming. To address this challenge, this study establishes a reliable CFD methodology to simulate and …
-
Kinematic variations between successful and unsuccessful dynamic rock climbing movements
… of the two-handed dynamic climbing maneuver (dyno). Participants received three attempts to complete a dyno on a 15° overhanging bouldering wall (EPIC Adventures) that were recorded via camcorder (Fastek Imaging; 30hz). MaxTRAQ software (v. 2.9.1.5; Innovision Systems) was used to digitize …
-
Development of a Semi Active Suspension System for Lightweight Automobiles
… damper was fabricated and tested using a shock dyno at CenTiRe. The test results were then compared to the simulation results so as to confirm performance of the damper. Additionally, the results obtained on the dyno were then compared against that of a relative single semi-active and passive …
-
DESIGN AND OPTIMIZATION OF LOW-Cu AND Cu-FREE AUTOMOTIVE BRAKE FRICTION MATERIALS
… and the full scale automotive brake dynamometer (Dyno) using a SAE J2430 test procedure. The SAE recommended a J2430 test procedure which provided the necessary data for the Brake Effectiveness Evaluation Procedure (BEEP) by the Brake Manufacturers' Council. The newly developed low-Cu and Cu-free …
-
Dynamic Temperature Model of an Automatic Transmission
… improved measurements on a vehicle in a chassis dyno were then performed. A decision to do measurements on all eight gears were made since the power losses were different on every gear. However the torque converter was open on the first gear, and could not be closed, which led to the decision to …
-
The management of foreign direct investment risk by three Norwegian firms in the 1960s and 1970s
… late 1960s and early 1970s. The three firms are: Dyno Industrier; Norcem; and Elkem-Spigerverket. Dyno invested in West Germany, England, Singapore, Denmark and Finland; Norcem invested in Ghana, Liberia, the Philippines, and Ras al-Khaimah; and Elkem-Spigerverket invested in the United Kingdom. …
-
Bio-Inspired Fins for High Performance Bodysurfing/Boarding
… to the hand planes, a flipper dynamometer (dyno) was developed to understand how fins increase the athlete’s performance and the aspects that lead to a good fin design. The flipper dyno went through an engineering design process, where the design was based on derived kinematics developed …
-
Investigation of direct-current brushed motor based energy regenerative automotive damper
… being manufactured. It was tested on a damper dyno, and results in terms of damping force, damping speed and regenerated electrical output were recorded. Further analysis and evaluation were conducted on the recorded data to relate to the numerical relations presented in the thesis. This …
-
Vehicle Simulation for Powertrain System Testing
… the need for a complete vehicle as in Chassis Dyno testing. Besides the test object which is physical hardware, software components containing all the models to replicate the complete vehicle testing are required. The correct functionality of the software component is vital; if one model …
-
System identification and control design for internal combustion engine variable valve timing systems
… system test bench and an engine dynamometer (dyno) are used to conduct the proposed multi-rate system identification using PRBS as excitation signals. Output covariance constraint (OCC) controllers were designed based upon the identified models. Performance of the designed OCC controller was …
-
Design of an Exhaust Gas Energy Recovery System for Internal Combustion Engines
… test engine was mounted onto a hydraulic engine dyno and a baseline of its power and torque output was recorded for final confirmation that the heat recuperated via this energy recovery system was not being negated elsewhere in the combined cycle. Finally, a preliminary steam turbine was designed …
-
An investigation into electric supercharging for emission reduction by means of engine downsizing
… be implemented on the selected vehicle for the dyno test purposes since it requires less power. Theoretical models for the engine, turbocharger and TurboClaw eSC including electric motor were created and validated. The system of all components was designed including control system and strategy. …
-
Assessment of technologies to reduce fuel consumption and pollutant emissions of modern passenger cars in real - world driving conditions
… engine operation was simulated on a laboratory dyno, where an identical engine was installed. Modifications were made to the exhaust aftertreatment system, including the replacement of the LNT system with an SCR system. The modifications reduced NOx emissions by 90%, achieving compliance with …
-
Suspension Controls and Parameter Estimation Using Accelerometer Based Intelligent Tires
… have been developed and simulated. A shock dyno is instrumented and skyhook and groundhook control algorithms have been implemented as well. In addition to this, a semi-active suspension switching based control algorithm is developed for reducing the effort of a direct moment yaw rate …
-
Stavitelný portál pro hydraulický pulzátor Inova
Diplomová práce se zabývá inovací současného testovacího zařízení nacházejícího se v laboratoři Ústavu konstruování. Inovace se týká konstrukčního návrhu portálové konstrukce, do které bude umístěn hydraulický pulsátor od firmy INOVA Praha s.r.o. Nová portálová konstrukce bude navržena s ohledem na …
-
Exhaust aftertreatment modeling for efficient calibration in diesel passenger car applications
… tests. Considering that test bench and chassis dyno experimental campaigns are costly and require a vast use of resources for the generation of data; therefore, reliable and computationally efficient simulation models are essential in order to identify the most promising technology mix to …
-
Oral Controlled Release Liquid Dosage Forms (Reconstitutable Powder) by Ion-exchange Resins
… complex was reduced to 10.65 ± 0.55 µm using Dyno mill. The drug-resin complex was layered on NP core 710-850 µm in a fluidized bed coater. The layering formulation was prepared with 20% HPMC E5 as a binder w/w of drug-resin complex. There was no increased drug release observed during first …
-
Study of Wear Mechanisms in Braking Systems with HVOF-Coated Discs
… real braking conditions for which specific dyno bench tests have been performed in further characterization tests. The pins used during the PoD characterization, made of three different commercially-available friction materials, had dimensions of 12 mm in height and 6 and 10 mm in diameter. …
-
DEVELOPMENT OF A DYNAMIC TORSIONAL ACTUATOR FOR TORQUE CONVERTER CLUTCH CHARACTERIZATION
This thesis outlines the development of a torsional shaker test stand capable of testing damping and isolation capabilities of torque converter clutch assemblies in automotive torque converters. By utilizing an electric motor typically found in hybrid electric vehicles, the desired torque …
-
Design of Timing Circuit for Fuel Injection Conversion and Development of Laboratory to Analyze Engine Performance Using a Dynamometer
A fundamental facility was built to analyze some of the basic parameters involved in engine performance, namely torque and power output of the engine. One of the objectives was to convert a carbureted engine into a fuel injection or (Fl) engine. This was achieved by designing and creating a timing …
Page 1 of 2