Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 21 for “"Edge chipping"”.

  1. Edge-Chipping and Translucency Comparison Among Lithium Silicate-Based Ceramics

    … of this in vitro study was to determine the edge-chipping toughness and the translucency of lithium silicate-based glass ceramics. Materials and Methods: Four lithium silicate/disilicate glass-ceramic materials, IPS e.max CAD and GC Initial LiSi blocks, and two zirconia-lithium silicate …

    marquette Repository record for Edge-Chipping and Translucency Comparison Among Lithium Silicate-Based Ceramics (opens in a new tab)

  2. Edge Chipping Resistance and Flexural Strength of Polymer Infiltrated Ceramic Network and Resin Nano Ceramic Materials

    … The purpose of this study was to measure the edge chipping resistance and flexural strength of the novel PICN and RNC materials and compare it to two commonly used feldspathic ceramic (FC) and leucite reinforced glass-ceramic (LRGC) CAD/CAM materials that share the same indications. Materials …

    marquette Repository record for Edge Chipping Resistance and Flexural Strength of Polymer Infiltrated Ceramic Network and Resin Nano Ceramic Materials (opens in a new tab)

  3. Analysis of machining damage to CAD/CAM block materials characterized by changes in surface roughness, edge chipping, and flexural strength

    PURPOSE: To analyze surface roughness, the edge chipping of different CAD/CAM bur milled dental materials (bar and crown design of 1.0mm and 1.5mm thickness), correlate the effect of machining damage on the material strength, compare the flexural strength of bur milled versus sectioned CAD/CAM …

    bu Repository record for Analysis of machining damage to CAD/CAM block materials characterized by changes in surface roughness, edge chipping, and flexural strength (opens in a new tab)

  4. An investigation of rock cutting: towards a novel design of cutting bits

    … the cone. Then, two stages of practical work, edge chipping and linear cutting, were set up to investigate the availability and further improvement of the pyramidal bit. An edge chipping test can be used to simulate the rock cutting process due to the similarity of crack systems. Such …

    unsw Repository record for An investigation of rock cutting: towards a novel design of cutting bits (opens in a new tab)

  5. Cutting edge controlled wear of alumina inserts

    … that the wear mechanisms along the cutting edge and at the flank wear land are distinctively different. The cutting edge wears by plastic rounding, microspallation and sporadic edge chipping, while edge breakage may occur for tools of imperfect microstructure. On the other hand, the wear …

    nus Repository record for Cutting edge controlled wear of alumina inserts (opens in a new tab) Download file for Cutting edge controlled wear of alumina inserts (opens in a new tab)

  6. Tool wear analysis in various machining processes and study of minimum quantity lubrication (MQL)

    … most dominant tool wear mechanism in milling. Edge chipping and micro-fracture were the tool failure modes. Overall, the double layer coating was superior to the triple layer coating under various cutting conditions due to the benefit coming from the coating deposition processes themselves. On …

    msu Repository record for Tool wear analysis in various machining processes and study of minimum quantity lubrication (MQL) (opens in a new tab)

  7. In-situ Micro and Nanomechanical Characterization and Ultrasonic Machining of Zirconia Ceramics

    … cyclic indentation imprints. Shear band, edge pile-ups, and microfractures were revealed in sintered zirconia indentation imprints. Advanced analysis of the zirconia materials deformation mechanisms revealed zirconia microstructures determined their cyclic nanoindentation induced …

    adelaide Repository record for In-situ Micro and Nanomechanical Characterization and Ultrasonic Machining of Zirconia Ceramics (opens in a new tab)

  8. Optinių paviršių formavimas skaidriose medžiagose lazeriniu frezavimu /

    … Process quality was evaluated by measuring edge chipping, sidewall roughness Ra, and the effect on the glass flexural strength. In surface shaping, the influence of laser pulse duration on structuring resolution and surface quality was analyzed by evaluating removed layer thickness and …

    vilnius Repository record for Optinių paviršių formavimas skaidriose medžiagose lazeriniu frezavimu / (opens in a new tab)

  9. A study of tool wear in turning of pure aluminum and drilling of CFRP/titanium stacks

    … coarser carbide grain.The evolution of Built up edge (BUE) in aluminum turning was studied. It was shown that the BUE decreased after the cobalt binder on the surface of the tool was removed by wear. The influence of oxidation in the formation of BUE is also discussed.In the CFRP/Ti stack …

    msu Repository record for A study of tool wear in turning of pure aluminum and drilling of CFRP/titanium stacks (opens in a new tab)

  10. Erosion and Roughness Modeling in Abrasive Jet Micro-machining of Brittle Materials

    … the formation and growth of lateral cracks, and edge chipping. Accuracy was further enhanced by simulating the actual relationship between particle size, velocity and radial location within the jet using distributions measured with high-speed laser shadowgraphy. The process of post-blasting AJM …

    toronto-retro Repository record for Erosion and Roughness Modeling in Abrasive Jet Micro-machining of Brittle Materials (opens in a new tab)

  11. Chipping and Wear of Glass Edges by the Low VelocityIimpact of Spherical Particles

    The edge rounding of brittle materials by vibratory finishing, VF, was investigated. Borosilicate glass and silicon nitride specimens were processed in two typical VF setups. In all cases, the processed specimens exhibited wear and chipping at their edges, whereas their flat surfaces remained …

    toronto-retro Repository record for Chipping and Wear of Glass Edges by the Low VelocityIimpact of Spherical Particles (opens in a new tab)

  12. Smart machining system platform for CNC milling with the integration of a power sensor and cutting model

    … based on a linear tangential force model with edge effect. The robustness of the model is verified through experiments with a wide variety of cutting conditions. Results show good agreement between measured and estimated power.A test platform has been implemented for performing research on …

    unh-thes Repository record for Smart machining system platform for CNC milling with the integration of a power sensor and cutting model (opens in a new tab)

  13. Fracture Resistance of Lithium Disilicate Restorations Following Endodontic Access Preparation; An In Vitro Study

    … Specimens that were examined under SEM showed edge chipping that involved primarily the glaze (IPS e.max Ceram) layer around the access openings. Endodontic access preparation of lithium disilicate restorations resulted in a significant decrease in the fracture resistance of the pressed (IPS …

    tamu Repository record for Fracture Resistance of Lithium Disilicate Restorations Following Endodontic Access Preparation; An In Vitro Study (opens in a new tab)

  14. Particleboard simulation model to improve machined surface quality

    … quality surfaces in one area and defects such as edge chipping in nearby areas. This research examines methods of improving surface quality by examining PB characteristics and their interactions with the cutting tool. It also develops an analytical model and software tool that allows the effects …

    ubc Repository record for Particleboard simulation model to improve machined surface quality (opens in a new tab) Download PDF for Particleboard simulation model to improve machined surface quality (opens in a new tab)

  15. Machinability of ceramic blanks for dental CAD/CAM restorations

    … as the minimum machined thickness. The edge chipping on the merlons’ wall was characterized. The chip counts, chipping length and chipping factor were compared by the effect of different machining conditions using statistical software JMP Pro 15. The second phase of the experiment aimed …

    bu Repository record for Machinability of ceramic blanks for dental CAD/CAM restorations (opens in a new tab)

  16. Towards a circular economy for chemically strengthened glass: Mechanochemical degradation and advanced remanufacturing

    … damage in toughened substrates, achieving an edge chipping threshold below 5 μm. In summary, the current research provides a robust scientific basis for assessing the functional viability of weathered CSG and delivers the manufacturing methodology required to implement a closed-loop CE …

    ets-quebec Download PDF for Towards a circular economy for chemically strengthened glass: Mechanochemical degradation and advanced remanufacturing (opens in a new tab)

  17. Stress analysis of metal cutting tools

    … because they directly applied the infinite wedge solution to determine stresses in the loaded region of the cutting tool. In this thesis, the tool and the boundary stresses are considered both in the loaded and free region. For a polynomial boundary stresses on the rake face and zero boundary …

    ubc Repository record for Stress analysis of metal cutting tools (opens in a new tab) Download PDF for Stress analysis of metal cutting tools (opens in a new tab)

  18. High Power Diode Laser Assisted Hard

    … and laser assisted grooving were cutting edge chipping, flank face abrasion, and adhesion. Built up edge (BUE) was invariantly present during LAM, which was very stable for low cutting speed (20 m/min) and became unstable with an increase in cutting speed to 30 m/min. The use of laser …

    mcmaster Repository record for High Power Diode Laser Assisted Hard (opens in a new tab)

  19. Properties and Applications of Polymer-Infiltrated Ceramic Network Materials

    … and 90% for the latter), highlighting some edge chipping in the first study, and debonding from the ti-base in the second. In conclusion, PICNs show a promising potential to be used in a variety of restorative applications, especially in minimally invasive dentistry, such as demonstrated in …

    liege Repository record for Properties and Applications of Polymer-Infiltrated Ceramic Network Materials (opens in a new tab) Download PDF for Properties and Applications of Polymer-Infiltrated Ceramic Network Materials (opens in a new tab)

  20. Modes and Progression of Tool Deterioration and Their Effects on Cutting Force During End Milling of 718Plus Ni-based Superalloy Using Cemented WC-CO Tools

    … deterioration features of the cutting tool edge. Experimentally, the study started by using a typical milling condition with both uncoated and coated cemented carbide (WC-Co) tools. Milling was conducted in either dry or wet conditions. After each pass of a selected distance, the tool was …

    auckland-tech Repository record for Modes and Progression of Tool Deterioration and Their Effects on Cutting Force During End Milling of 718Plus Ni-based Superalloy Using Cemented WC-CO Tools (opens in a new tab)

Page 1 of 2