Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 21 for “"Fibrous composites Testing"”.
-
An investigation of the excitation frequency dependent behavior of fiber reinforced epoxy composites during vibrothermographic inspection
… behavior of delaminations in fiber reinforced composites during vibrothermography, the use of active thermography with a mechanical excitation for the nondestructive evaluation of a structure or part. Two models, one where the size and geometry of the flaw control a local resonance and the …
-
Developments in moire interferometry: carrier pattern technique and vibration insensitive interferometers
… (with the thickness of 125 μm) in graphite/epoxy composites and strain concentrations in the resin-rich zones (with the thickness of 10 μm) between neighboring plies are revealed by the carrier fringe technique. Three experiments are presented to show the effectiveness of the application of …
-
The compressive failure of graphite/epoxy plates with circular holes
The results of an experimental investigation into the compressive behavior of T300-5208 graphite/epoxy plates measuring 12.70 cm by 25.40 cm and containing circular cutouts ranging to 3.81 cm are reported. Two thicknesses, 24 ply and 48 ply were chosen to differentiate between stability failures …
-
Stiffness reduction resulting from transverse cracking in fiber- reinforced composite laminates
Several damage modes, including fiber breakage, delamination, and transverse cracking, have been observed to contribute to the mechanical degradation of fiber-reinforced composite laminates. In this investigation, the effect of transverse cracking on laminate stiffness was studied. Four. …
-
Effect of processing induced defects on the failure characteristics of graphite epoxy angles
The objective of this study was to investigate the bending strength and failure characteristics of AS4/3501-6 and AS4/1806 graphite/epoxy angles sections as a function of processing induced defects and porosity. The angle sections were removed from 30-inch long angles fabricated at Lockheed Georgia …
-
Multi-sensor fusion for nondestructive inspection of fiber reinforced composite structures
Thesis (M.S.)--Michigan State University. Dept. of Computer Science, 1991
-
Fiber waviness and bonding conditions on composite performance by homogenization method
Thesis (Ph. D.)--Michigan State University. Department of Materials Science and Mechanics, 1996
-
Dynamic mechanical analysis of graphite/epoxy composites with varied interphases
Dynamic mechanical analysis (DMA) has been used extensively to characterize polymeric materials. This thesis investigates the use of this technique to characterize composite materials. Four material systems, all having the same fiber and the same matrix material, were systematically altered with …
-
Adhesion between Nextel 312 [trademark] fibers and Blackglas [trademark] silicon oxycarbide and its effect on composite properties
Thesis (M.S.)--Michigan State University, Department of Chemical Engineering and Materials Science, 2003
-
Durability of adhesive joints between concrete and FRP reinforcement in aggressive environments
The durability of the bondline between concrete and its fiber-reinforced polymer reinforcement was characterized at various temperature and humidity levels. The bondline consisted of an epoxy primer, an epoxy putty and an epoxy saturant. In principle, fracture could occur anywhere in this bondline, …
-
The compressive failure of aligned fiber composite materials
… understanding of the compressive behavior of fibrous composites is somewhat limited. Reliable compressive test methods are one of the keys to understanding the complex compressive failure process in these materials. Compressive test devices that are currently in use often encounter …
-
Development of an experimental facility for biaxial compressive testing of fiber composite materials
… purpose of this study was the development of a testing facility and test specimen for the characterization of laminated composites under biaxial compressive stress states. A biaxial testing facility capable of applying almost arbitrary stress paths in the in-plane compressive stress regime, to …
-
Mechanical and Fracture Behavior of Additively Manufactured Carbon Fiber Reinforced Polymer Composites with Bouligand Mesotrstructure
Carbon fiber reinforced polymer (CFRP) composites are strong and lightweight materials commonly used in aerospace, automotive, and construction industries. Biomaterials offer various unique meso-structures in creating CFRP composites with superior mechanical properties. In this study, we examined …
Page 1 of 2