Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 13 of 13 for “"Finite element method--Models"”.

  1. Analysis of Random Structure-Acoustic Interaction Problems Using Coupled Boundary Element and Finite Element Methods

    A coupled boundary element(BEM)-finite element(FEM) approach is presented to accurately model structure-acoustic interaction systems. The boundary element method is first applied to interior, two and three-dimensional acoustic domains with complex geometry configurations. Boundary element results …

    odu Repository record for Analysis of Random Structure-Acoustic Interaction Problems Using Coupled Boundary Element and Finite Element Methods (opens in a new tab)

  2. A 3D Active Microwave Imaging System for Breast Cancer Screening

    … into human breast tissue. 3D full-wave finite element method models of this imaging chamber, complete with full antenna geometry, have been developed using Ansoft HFSS and verified experimentally. In addition, an electronic switching system using Gallium Arsenide (GaAs) absorptive RF …

    duke Repository record for A 3D Active Microwave Imaging System for Breast Cancer Screening (opens in a new tab)

  3. Surface acoustic wave sensor for low concentration mercury vapor detection

    … effective mass density. In this thesis, common methods for sensing mercury vapor concentration were summarized and a surface acoustic wave (SAW) sensor utilizing the adsorption of mercury on gold electrodes was proposed for 1 μg/m3 level low concentration mercury vapor detection. The working …

    bu Repository record for Surface acoustic wave sensor for low concentration mercury vapor detection (opens in a new tab)

  4. The Modeling of Structural-Acoustic Interaction Using Coupled FE/BE Method and Control of Interior Acoustic Pressure Using Piezoelectric Actuators

    A coupled finite element (FE) and boundary element (BE) approach is presented to model full coupled structural/acoustic/piezoelectric systems. The dual reciprocity boundary element method is used so that the natural frequencies and mode shapes of the coupled system can be obtained, and to extend …

    odu Repository record for The Modeling of Structural-Acoustic Interaction Using Coupled FE/BE Method and Control of Interior Acoustic Pressure Using Piezoelectric Actuators (opens in a new tab)

  5. Development of a Capacitive Sensor for In-Pile Materials Monitoring

    … is estimated through physics-based simulation models of irradiation-, temperature-, pressure-, etc.-induced material degradation. model predictions are validated with the measurement and characterization of fuel pin evolution. Linear voltage differential transformers (LVDT) are commonly used to …

    ut-knoxville Repository record for Development of a Capacitive Sensor for In-Pile Materials Monitoring (opens in a new tab)

  6. Optimisation of generators for direct drive offshore wind turbines

    … electromagnetic and structural generator models are introduced for a surface-mounted magnet generator topology (using magnets with high BHmax) and a flux-concentrating variant (using magnets with both higher and lower BHmax). Finite element method models are used to check key dependent …

    strathclyde Repository record for Optimisation of generators for direct drive offshore wind turbines (opens in a new tab)

  7. Nanophotonics with Group III–V Compound Semiconductor Nanowires

    … presented by their bottom-up growth methods. For research and design of such nanophotonics devices, numerical optics modeling is an invaluable tool which helps to increase the physical understanding of the device operation and to reduce costly and time-consuming prototyping. This …

    aalto Repository record for Nanophotonics with Group III–V Compound Semiconductor Nanowires (opens in a new tab)

  8. Numerical Modelling of Eddy Current Probes for CANDU® Fuel Channel Inspection

    … measurement errors. Validated mathematical models of the EC probe are very useful for data interpretation, and may improve the gap measurement under inspection conditions where these parameters vary. As a first step, exact solutions for the electromagnetic response of a transmit-receive coil …

    queens Repository record for Numerical Modelling of Eddy Current Probes for CANDU® Fuel Channel Inspection (opens in a new tab)

  9. A measurement method for damping of drive shaft

    … i.e. the drive shaft. The goal is to find a test method for controlling the damping in the drive shaft for quality purposes. An additional goal is to see if the method also could secure the target value for the sound pressure level in a drive-by test. Using cardboard tubes inside the drive shafts …

    chalmers Repository record for A measurement method for damping of drive shaft (opens in a new tab)

  10. Εμβιομηχανική μελέτη της σπονδυλικής στήλης με πεπερασμένα στοιχεία και με πτωματικούς σπονδύλους

    … was to construct a detailed, three-dimensional finite element method (FEM) model in order to study the mechanical behavior of the lumbar spine after several loading conditions. Also to validate the results using data from mechanical testing of cadaveric vertebrae. An anatomically accurate …

    greece Repository record for Εμβιομηχανική μελέτη της σπονδυλικής στήλης με πεπερασμένα στοιχεία και με πτωματικούς σπονδύλους (opens in a new tab)

  11. Dynamic finite element modeling and analysis of a hermetic reciprocating compressor

    Dynamic finite element modeling and analysis of a refrigeration compressor was investigated as part of a noise emission study. Natural frequencies and normal mode shapes were calculated for the major structural components of the compressor. The components were later combined to form a model of the …

    vt Repository record for Dynamic finite element modeling and analysis of a hermetic reciprocating compressor (opens in a new tab)

  12. Component-wise Analysis of Reinforced Thin-walled Metallic and Composite Structures

    … possible to have structural continuity between elements on which it is realized, such as the plate, stringers, and ribs. In fact, when a reinforced structure is realized using a milling machine, the stringer derives from the same work-piece and inevitably the continuity between plate and …

    poli-torino Repository record for Component-wise Analysis of Reinforced Thin-walled Metallic and Composite Structures (opens in a new tab)