Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 88 for “"Fracture strain"”.

  1. Fracture toughness degradation in HY-80 and HY-100 after prestraining

    … to discover the mechanism by which the fracture toughness J sub 1C, of HY-series steel decreases with increasing prestrain at room temperature. This decrease J sub 1C is a function of yield strength and plane strain fracture strain. However, this reduction in J sub 1C is shown to be …

    nps Repository record for Fracture toughness degradation in HY-80 and HY-100 after prestraining (opens in a new tab)

  2. Experimental study of solder/copper interface under varying strain rates

    … when subjected to dynamic axial loads at strain rates between 10.0 s-1 and 0.05 s-1. The copper is alloy 101 and the lead-free solder has a composition of 96% tin and 4% silver. The tests results revealed that as the strain rate increases so do the ultimate and yield strengths but the …

    nps Repository record for Experimental study of solder/copper interface under varying strain rates (opens in a new tab)

  3. Fabrication and Testing of Nanoscale Reinforced UHMWPE Fibers and Their Composites

    … and UHMWPE + 10 wt.% PVP/PVDF coated fibers. Strain hardening was performed on the produced fibers, and mechanical testing was performed in order to determine the properties of fibers. The mechanical properties of the fibers involved the ultimate tensile strength, young’s modulus, fracture …

    gsu Repository record for Fabrication and Testing of Nanoscale Reinforced UHMWPE Fibers and Their Composites (opens in a new tab)

  4. Tensile Properties and Fracture Behaviour of Multipass Friction Stir Processed Al-7Si-0.3Mg Cast Alloy

    … the processed material, and hence to explain the fracture behaviour of the MP-FSPed material. Experimentally, cast plates of A356 (Al-7Si- 0.3Mg) alloy were made. Initial set of experiments with a high tool rotation speed (ω rpm) was conducted to produce maximum stir zone area. However, on finding …

    auckland-tech Repository record for Tensile Properties and Fracture Behaviour of Multipass Friction Stir Processed Al-7Si-0.3Mg Cast Alloy (opens in a new tab)

  5. The mechanical properties of reinforcing steel bars at low temperature.

    … by means of three calibrated load cells. The strains were measured with a 2" gage length extensometer, and the fracture strain was measured with calipers. The results of the tension tests showed that the yield and fracture stresses increase with decreasing temperature. The magnitude of the …

    ottawa-retro Repository record for The mechanical properties of reinforcing steel bars at low temperature. (opens in a new tab)

  6. Correlation of microstructure, tensile properties and hole expansion ratio in cold rolled advanced high strength steels

    … shear face characterization showed that the fracture and burr region affect HER. The HER decreases with increasing size of fracture and burr region. With a larger fracture and burr region more defects and/or micro-cracks will be present on the shear surface. This larger fracture region on the …

    colo-mines Repository record for Correlation of microstructure, tensile properties and hole expansion ratio in cold rolled advanced high strength steels (opens in a new tab)

  7. Fracture abundance and strain in folded cardium formation, Alberta fold-and-thrust belt, Canada

    … Understanding the distribution of natural fractures, their evolution, and timing of formation relative to the evolution of the fold-and-thrust system could potentially improve exploration and development outcomes in these otherwise tight unconventional reservoirs. However, the formation of …

    texas Repository record for Fracture abundance and strain in folded cardium formation, Alberta fold-and-thrust belt, Canada (opens in a new tab)

  8. Engineering Hydrogels to Tune Mechanical Properties

    … ratio, shear (G) and elastic (E) moduli, and fracture properties of the gels were then investigated. Chondroitin sulfate (CS) and hyaluronic acid (HA) as macromers, oligo(ethylene glycol) diacrylates (OEGDA) as comonomers, and acrylamide to form double networks (DN) were the focus of this …

    ku Repository record for Engineering Hydrogels to Tune Mechanical Properties (opens in a new tab)

  9. Numerical simulation of effects of cladding and superimposed hydrostatic pressure on fracture in metals under tension.

    … />and superimposed hydrostatic pressure on fracture in metals under tension by using<br />finite element software ABAQUS/Explicit. It is concluded that both cladding and<br />superimposed hydrostatic pressure delay void nucleation and void growth, which<br />results in increasing fracture …

    mcmaster Repository record for Numerical simulation of effects of cladding and superimposed hydrostatic pressure on fracture in metals under tension. (opens in a new tab)

  10. Fracture Characterization and Damage Accumulation Modelling of DP1180 Steel under Proportional and Non-Proportional Loading

    … strength-to-weight ratio. However, their complex fracture behavior under multiaxial and non-proportional loading conditions presents challenges for accurate failure prediction in structural simulations. This thesis aims to address these challenges through a systematic experimental investigation …

    waterloo Repository record for Fracture Characterization and Damage Accumulation Modelling of DP1180 Steel under Proportional and Non-Proportional Loading (opens in a new tab)

  11. Influence of Boundary Conditions on the Sheared Edge Fracture Limits of a 3rd Generation Advanced High Strength Steel.

    … experiments rely upon the input of a single fracture strain value to predict edge cracking in stamped parts, disregarding the effects of deformation mode and element size. An efficient and reliable modeling approach for edge failure is required without having to simulate the shear cutting …

    waterloo Repository record for Influence of Boundary Conditions on the Sheared Edge Fracture Limits of a 3rd Generation Advanced High Strength Steel. (opens in a new tab)

  12. Numerical models for natural fibre composites with stochastic properties

    … between 6 mm and 300 mm and the Young’s modulus, strain to failure and ultimate tensile strengths were determined individually. A strong correlation was observed between the fibre strength/fracture strain and fibre gauge length. It was found as the gauge length increases the fibre …

    plymouth Repository record for Numerical models for natural fibre composites with stochastic properties (opens in a new tab)

  13. FINITE ELEMENT ANALYSIS OF MECHANICAL BEHAVIOR OF MECHANICAL COMPONENTS UNDER COMPRESSION

    … hydrostatic pressure on ductility and fracture strain of compressed rings, using the ABAQUS/Explicit solver. As hydrostatic pressure increases, the stress state at the cross-section of the ring changes, and the tensile radial and tangential stress components become compressive. …

    mcmaster Repository record for FINITE ELEMENT ANALYSIS OF MECHANICAL BEHAVIOR OF MECHANICAL COMPONENTS UNDER COMPRESSION (opens in a new tab)

  14. Development of a method for prediction of water ballast tank coating failure

    … industry. The consequences of coating failures (fracture) are corrosion of the steel which can lead to early occurrence of fatigue cracks and fast fatigue crack propagation. Inspections of coatings in water ballast tanks of ships have shown that fracture of many coatings occurs earlier than their …

    chalmers Repository record for Development of a method for prediction of water ballast tank coating failure (opens in a new tab)

  15. The effect of microstructure on strain localization in the precipitate free zone of Al-Mg-Si alloys

    … ductility as characterized by the true fracture strain in a tensile test. However, most of the data in the literature is based on qualitative experimental observations, or more recently, polycrystal plasticity simulations. The lack of quantitative measurements limits the predictive …

    ubc Repository record for The effect of microstructure on strain localization in the precipitate free zone of Al-Mg-Si alloys (opens in a new tab) Download PDF for The effect of microstructure on strain localization in the precipitate free zone of Al-Mg-Si alloys (opens in a new tab)

  16. The influence of non-metallic inclusions upon the properties of linepipe steels

    … nearest-neighbour distance NND) correlated with fracture strain. An increase in inclusion volume fraction and/or the dimension of inclusions on a plane parallel to the plane of fracture led to a decrease in fracture strain. The inclusion parameters did not correlate with the fracture strains for …

    aston Download PDF for The influence of non-metallic inclusions upon the properties of linepipe steels (opens in a new tab)

  17. Embrittlement of zinc crystals by mercury

    … stage A and stage B (2) decrease in transition strain from stage A to stage B (3) decrease in fracture stress and fracture strain. The results have been interpreted in the context of the present understanding of deformation theory of C.P.Hex. metals. In addition, relevant mechanisms for crack …

    ubc Repository record for Embrittlement of zinc crystals by mercury (opens in a new tab) Download PDF for Embrittlement of zinc crystals by mercury (opens in a new tab)

  18. Development of high performance hybrid syntactic foams: structure and material property characterization

    … foams demonstrate poor damage tolerance and low fracture strain, when compared with low density syntactic foams, which exhibit higher damage tolerance and fracture strains. The present study deals with increasing the fracture strain and damage tolerance properties of high density syntactic foams. …

    lsu-thes Repository record for Development of high performance hybrid syntactic foams: structure and material property characterization (opens in a new tab)

  19. Synthesis and Characterization of Hydrogels Based on Poly (N-vinyl formamide)

    … by conducting tensile tests to measure fracture stress, fracture strain, Young's modulus (E) and shear modulus (G). Young's modulus of PNVF gels increased from 138 kPa to 609 kPa, shear modulus increased from 49 to 212 kPa, fracture stress increased from 17 to 66 kPa where as the …

    ku Repository record for Synthesis and Characterization of Hydrogels Based on Poly (N-vinyl formamide) (opens in a new tab)

  20. Effect of strain and strain rate on the microstructure of a superplastically deformed Al-10%Mg-0.1%Zr alloy.

    … testing was done at various temperatures and strain rates and superplastic elongations were observed for both alloys. Subsequently, samples of Al-1 0%Mg-0. 1 %Zr were tested at 300°C to strains ranging from 8% to 267% as well as to fracture. Strain rates of 6.67 X 10~ 3 S" 1 and 6.67 X 10"4 S" …

    nps Repository record for Effect of strain and strain rate on the microstructure of a superplastically deformed Al-10%Mg-0.1%Zr alloy. (opens in a new tab)

Page 1 of 5