Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 240 for “"Friction coefficients"”.
-
Dynamical Friction Coefficients for Plasmas Exhibiting Non-Spherical Electron Velocity Distributions
This investigation is designed to find the net rate of decrease in the component of velocity parallel to the original direction of motion of a proton moving through an electron gas exhibiting a non-spherical velocity distribution.
-
Automobile Safety Systems: Improvement of a Method to Estimate Tire Friction Coefficients in Passenger Vehicles
… constrained by the adhesion limit given by the friction coefficient, knowledge of the road conditions is an important factor in their performance. This project analyzes an estimation structure which allows the estimation of real time tire friction coefficients with the road using measurements of …
-
Quantifying the Effect of Friction Coefficients on the Sim-to-Real Gap in Mobile Robot Path Tracking Simulations on Varied Terrain
… are, or how simulation parameters such as the friction coefficient may impact the sim-to-real gap in practical use cases. To support a more nuanced and resource-effective application of simulations, this thesis presents the validation of several mobile robot path-tracking simulations in the …
-
Use of Lidar Data to Investigate the Influence of Bottom Friction Coefficients for Storm Surge Modeling of Hurricane Michael in the Florida Panhandle
… calculate spatially variable Manning’s roughness coefficients (n). This is the first time the process has been applied at the multi-county scale. Using the numerical hydrodynamic modeling code ADCIRC, an unstructured finite element mesh (NGOM-RT) was used to simulate storm surge using both the …
-
A Study on the Effects of Cementless Total Knee Arthroscopy Implants' Surface Morphology with Finite Element Analysis
… fit and the roughness, or coefficient of friction, between implant and bone. Stress shielding is a comparison of the properties in implanted bone to natural bone; it is a commonly used measurable when using a finite element model to optimize implant design. The purpose of this study is to …
-
Modeling of dynamic friction in vibration environment for heavy vehicle load security
… important factor for all road users, and the friction forces arising within the cargo layer and between the cargo and the trailer bed are known to offer definite resistance to the dynamic forces and moments induced by the directional maneuvers, which would affect the load security …
-
Turbulent flow characteristics over realistic ice roughness on simulated NACA 0012 airfoils.
… codes are possible by characterizing the skin friction caused by ice roughness along airfoils more accurately. Previous studies at Baylor University have explored convective enhancements caused by ice roughness over a flat plat under accelerated and non-accelerated conditions. This paper is a …
-
Mechanism and experimental validation of innovative self-centering conical friction damper
… a novel damper named self-centering conical friction damper (SCFD) is proposed. SCFD utilizes conical, flat surfaces and post-tensioning tendons to resist the earthquake loads in all directions. The conical surfaces force the SCFD to self-center, making the SCFD highly desired for earthquake …
-
Measurements of surface shear stresses under a three-dimensional turbulent boundary layer using oil-film laser interferometry
… the data extracted from the data records. Skin friction directions computed using a least square error fit were compared to angles obtained from surface oil flows, hot wire anemometry, and LDV measurements. Also, the magnitude of the skin friction coefficients were compared to independently …
-
Wall functions for the k - [epsilon] turbulence model in generalized nonorthogonal curvilinear coordinates
… both orthogonal and nonorthogonal grids, and the friction coefficients and velocity profiles compared with a semi-empirical equation. Flow over a body of revolution at zero angle of attack was then computed to test the method's ability to handle flow over a curved surface. Friction coefficients …
-
Optimization-based analysis of rigid mechanical systems with unilateral contact and kinetic friction
… systems with unilateral contact and Coulomb friction is to formulate the contact forces (or impulses) as the unknowns of a linear complementarily problem (LCP). However, the solution set of an arbitrary LCP may be nonconvex, which poses the following computational and theoretical problems: if …
-
Sliding Friction and Wear Behavior of High Entropy Alloys at Room and Elevated Temperatures
… elevated (100°C and 300°C) temperature sliding friction coefficients and wear rates were determined for five HEAs: Co0.5 Cr Cu0.5 Fe Ni1.5 Al Ti0.4; Co Cr Fe Ni Al0.25 Ti0.75; Ti V Nb Cr Al; Al0.3CoCrFeNi; and Al0.3CuCrFeNi2. Wear surfaces were characterized with scanning electron microscopy and …
-
Testing geologic and geometric effects on drilling operations using torque and drag models
… otherwise. Lesage et al. (1988) wrote that friction coefficients are not affected by lithology and hole angle, among other things. And if friction coefficients are similar for all of these factors, then only inclination, azimuth, and pipe specifications affect torque and drag. My thesis …
-
Friction and Leakage Characteristics of Inflatable Structures in Tunnels
… and tunnel was recorded and used to calculate a friction coefficient. Friction coefficients were calculated for three different materials lining the tunnel so a comparison could be made. These friction coefficients were also compared to laboratory friction machine testing of the same lining …
-
Modelling of the mechanical behaviour of clips for automotive interior panels
… between clip and bracket. The effects of various friction coefficients between parts are studied and a combination of friction coefficients that correlate well to measured sliding capability is presented. The behaviour in terms of torsional stiffness in the clip joint was discovered to be …
-
Ultrahigh vacuum studies of the boundary lubrication of metals
… species as a function of coverage. The friction behavior of clean Cu(111) surfaces was characterized by stick-slip sliding behavior and high static friction coefficients.
-
A study of the role of friction in superplastic blow forming of alloy sheet
… with the poor level of current understanding of friction behaviour in the SPF process. It is thus the aim of this research to investigate the superplastic blow forming process and the role of friction, to minimize uneven component thinning to meet design criteria. The objective was tackled by way …
-
The Influence of Surface Roughness and Its Geometry on Dynamic Behavior of Water Droplets
… the contact line fluctuations and contact line friction coefficients of water droplets on smooth, one-tier, and two-tier (with carbon nanotubes (CNTs) grown on Si micropillars) surfaces in Chapters 4 and 5. Both the advancing and receding contact line fluctuations/friction coefficients have been …
Page 1 of 12